|
This is the modern view of the Yesterday's Tractors Forums. Just login with your YT Userid and password to post. If you have trouble logging in, contact us by email to support at ytmag.com, or through the Reader Form, and we will get you going right away.
| View previous topic :: View next topic |
| Author |
Message |
goatboy
Regular
Joined: 05 Mar 2009
Posts: 67
Report to Moderator
|
 Posted: Sun Dec 09, 2012 5:14 am Post subject: Moline UTS front end swap |
  |
|
Not Sure if I want to do this but I have a UTS can I put a tricycle front end on it. I assume you can swap one out from a regular U.
|
|
| Back to top |
|
 |
Jeff Gravert
Regular
Joined: 27 Jul 2008
Posts: 218
Report to Moderator
|
| Posted: Sun Dec 09, 2012 10:11 am Post subject: Re: Moline UTS front end swap |
|
|
Yes you can do that but you need to switch the whole front casting. The front frame rails are the same and the radiator mounts the same. Jeff
|
|
| Back to top |
|
|
MrMark
New User
Joined: 20 Apr 2008
Posts: 19
Report to Moderator
|
| Posted: Sun Dec 09, 2012 1:23 pm Post subject: Re: Moline UTS front end swap |
|
|
Prsonally I would not change it but that is up to you. One thing I can say is, if it is a straight axle I have switched to the arched front axle. If it is adjusted correctly it will steer easier and turn shorter than the straight axle.
|
|
| Back to top |
|
|
molinegb
Long Time User
Joined: 13 Feb 2005
Posts: 904
Report to Moderator
|
| Posted: Mon Dec 10, 2012 7:08 am Post subject: Re: Moline UTS front end swap |
|
|
You also have to change steering box and associated steering linkage.
|
|
| Back to top |
|
|
1031D
Tractor Expert
Joined: 31 Jul 2004
Posts: 1706
Location: Southern Wisconsin
Report to Moderator
|
| Posted: Mon Dec 10, 2012 9:54 am Post subject: Re: Moline UTS front end swap |
|
|
Why not go and buy a regular U? It would never look or ride right unless you had 38" rear rubber too. The steering and complete front end is different.
|
|
| Back to top |
|
|
goatboy
Regular
Joined: 05 Mar 2009
Posts: 67
Report to Moderator
|
| Posted: Fri Dec 14, 2012 1:38 pm Post subject: Re: Moline UTS front end swap |
|
|
Thanks for the info, I think I am going to keep the wide front.
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
|
|
Discount Prices for Parts! You can help support this extensive website by purchasing your tractor parts, manuals and merchandise from our [ Antique Tractor Store ] or call our friendly sales staff toll free (800) 853-2651. [ More Info ]
|
YT Home
| Tractor Manuals
| Tractor Parts
| Forum Home
Copyright © 1997-2013 Yesterday's Tractor Co. - A Washington State Corporation
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
