Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

oliver 88 clutch


 
Post new topic    
View previous topic :: View next topic  
Author Message
Gary in W I
New User


Joined: 11 Dec 2012
Posts: 1


Report to Moderator

PostPosted: Tue Dec 11, 2012 6:33 pm    Post subject: oliver 88 clutch Reply to specific post Reply with quote

Ihave an oliver88 we are trying to put a clutch in, and we"re having trouble to get enough free-play to be able to shift it. We"ve done everything according to the book, wondering if anyone else had that problem and can give me any ideas of what to do. It"s an 11 inch clutch. Thanks!
 
Back to top
View user's profile
J. Schwiebert
Guest






Report to Moderator

PostPosted: Wed Dec 12, 2012 3:45 am    Post subject: Re: oliver 88 clutch Reply to specific post Reply with quote

I read this that the clutch does not release. Is this an older 88 with the bushing type pilot bearing or a later 88 with the ball type pilot bearing? No matter which type did you change it? Next question how much free travel do you have the way you have it adjusted now?
 
Back to top
benelli7979
Guest






Report to Moderator

PostPosted: Wed Dec 12, 2012 6:34 am    Post subject: Re: oliver 88 clutch Reply to specific post Reply with quote

Did you check the pressure plate finger height?
 
Back to top
JDSNOW
Regular


Joined: 11 Oct 2011
Posts: 24


Report to Moderator

PostPosted: Wed Dec 12, 2012 2:23 pm    Post subject: Re: oliver 88 clutch Reply to specific post Reply with quote

Been there had same problem. Problem was wrong pressure plate and disc. Fingers were hitting rivets on dics. I took it all apart again to figure it out. Yes dealer sent proper parts for free then.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Oliver, Cletrac, Coop and Cockshutt All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters