Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

2 cylinder head gasket...what are pullers using?


 
Post new topic    
View previous topic :: View next topic  
Author Message
charger66
Regular


Joined: 28 Oct 2009
Posts: 76


Report to Moderator

PostPosted: Sat Dec 15, 2012 6:52 am    Post subject: 2 cylinder head gasket...what are pullers using? Reply to specific post Reply with quote

Hey guys. Wondering what brand of head gasket the 2 lung high compression pullers are using or prefer? I got a B that will be about 9:1 and see heavy use, pulling, plowing, synopsis, belt work at rollag, etc. Anyone use the sets off this site?

Thanks

"Infected"
 
Back to top
View user's profile
charger66
Regular


Joined: 28 Oct 2009
Posts: 76


Report to Moderator

PostPosted: Sat Dec 15, 2012 6:54 am    Post subject: Re: 2 cylinder head gasket...what are pullers using? Reply to specific post Reply with quote

Stupid phone....dyno I meant
 
Back to top
View user's profile
jd b puller
Tractor Expert


Joined: 07 Jul 2001
Posts: 3179
Location: North Carolina

Report to Moderator

PostPosted: Sat Dec 15, 2012 7:26 am    Post subject: Re: 2 cylinder head gasket...what are pullers using? Reply to specific post Reply with quote

11+ compression, 6.125" bore, 442 cubes, E-85, stock head gasket (actually reused it once). Any other questions? :-)

Make sure the block and head are flat, and use new studs.
 
Back to top
View user's profile Visit poster's website
nl00sb
Regular


Joined: 01 Nov 2009
Posts: 329


Report to Moderator

PostPosted: Sat Dec 15, 2012 8:57 pm    Post subject: Re: 2 cylinder head gasket...what are pullers using? Reply to specific post Reply with quote

my b is 14-1 with stock head gasket been in there for years maybe lucky idk
 
Back to top
View user's profile
charger66
Regular


Joined: 28 Oct 2009
Posts: 76


Report to Moderator

PostPosted: Sat Dec 15, 2012 9:14 pm    Post subject: Re: 2 cylinder head gasket...what are pullers using? Reply to specific post Reply with quote

Stupid phone....dyno I meant
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Pulling All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters