Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Input shaft


 
Post new topic    
View previous topic :: View next topic  
Author Message
Schim
Regular


Joined: 23 Jan 2011
Posts: 393


Report to Moderator

PostPosted: Tue Dec 18, 2012 2:53 pm    Post subject: Input shaft Reply to specific post Reply with quote

Have to replace the input shaft on my S88. Pulled out the old one last night and compared it to the other (good) one that I have. My good one is like 1/4 inch longer than the old one. Is this out of an 880 or something? can I use it in my S88? It will not be running a belt pulley. I have pics of the 2 if anyone wants to see them side by side.
 
Back to top
View user's profile
rocko
Regular


Joined: 15 Feb 2010
Posts: 407


Report to Moderator

PostPosted: Tue Dec 18, 2012 4:41 pm    Post subject: Re: Input shaft Reply to specific post Reply with quote

schim isn't there a coupler between that shaft and the tranny shaft or I'm I way off base and thinking of a differfnt part? Rocko.
 
Back to top
View user's profile
Schim
Regular


Joined: 23 Jan 2011
Posts: 393


Report to Moderator

PostPosted: Tue Dec 18, 2012 6:48 pm    Post subject: Re: Input shaft Reply to specific post Reply with quote

Yes there is but I"m replacing the shaft that goes into the tranny. Maybe I could just cut off a quarter inch off the back side that sticks in the tranny side? If its an issue that is...
 
Back to top
View user's profile
J. Schwiebert
Guest






Report to Moderator

PostPosted: Tue Dec 18, 2012 6:51 pm    Post subject: Re: Input shaft Reply to specific post Reply with quote

Why not show the picture and lay them so the shafts are even across the front. We used to saw a lot of those shafts off if they had a power lift and I am sure there was a litt lvariation in the length.
 
Back to top
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Oliver, Cletrac, Coop and Cockshutt All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters