Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Webster Compressor Info needed.


 
Post new topic    
View previous topic :: View next topic  
Author Message
Crash5291
New User


Joined: 19 Dec 2012
Posts: 4


Report to Moderator

PostPosted: Wed Dec 19, 2012 1:14 pm    Post subject: Webster Compressor Info needed. Reply to specific post Reply with quote

I just picked up this unit i"m looking to find specs on the pump setup
(CFM rating and rpm)

and a recommendation for a gas motor size to run it.


The unit is on its original tray as far as i can tell, on the tray it
has
Model: R
Serial: 3264

On the pump itself has Serial: 4611
pump as 3 spoke 9" pulley (OD) with an attached after cooler i"m
guessing

Thoughts?

Thanks Joe
 
Back to top
View user's profile
XRogerX
Regular


Joined: 05 Mar 2009
Posts: 142


Report to Moderator

PostPosted: Wed Dec 19, 2012 1:49 pm    Post subject: Re: Webster Compressor Info needed. Reply to specific post Reply with quote

If you know the first stage displacement in cubic inches, divide by 10 and it will give you the electric motor horsepower required to run it. A good safe margin is to double that for a gas engine. FYI, the model of the pump is the first two digits of the pump serial number, therefore, according to that, you have a model 46 pump, which I have never heard of. I do know that thee was a Model 45 pump, and you can check another YTMag post for some info that I have mostly forgotten over the years!
Webster Stuff.

 
Back to top
View user's profile
Crash5291
New User


Joined: 19 Dec 2012
Posts: 4


Report to Moderator

PostPosted: Wed Dec 19, 2012 2:22 pm    Post subject: Re: Webster Compressor Info needed. Reply to specific post Reply with quote

Here is a few pictures i took,









Can i reuse the head gasket without issue? (if it comes apart ok) as i will have to pull the head to check the bore/stroke to figure that out.

It has a 1725RPM 1/4hp (5.0A) motor(2" pulley) but it stalls out at about 50 PSI.


Thanks
Joe
 
Back to top
View user's profile
Crash5291
New User


Joined: 19 Dec 2012
Posts: 4


Report to Moderator

PostPosted: Thu Dec 20, 2012 8:39 am    Post subject: Re: Webster Compressor Info needed. Reply to specific post Reply with quote

Just placed a call to Regional Compressor Ottawa
he had limited information on it

From what he did have its 900 RPM max and 1/2-1HP and he figured around 2cfm

Thanks
Joe
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Tool Talk All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters