Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Distributor O-ring for a TO-35 with Z134 engine


 
Post new topic    
View previous topic :: View next topic  
Author Message
Checkptchickee
Regular


Joined: 30 Jan 2011
Posts: 20


Report to Moderator

PostPosted: Fri Dec 28, 2012 12:56 pm    Post subject: Distributor O-ring for a TO-35 with Z134 engine Reply to specific post Reply with quote

Can someone tell me the size of the o-ring that goes on the delco distributor (clamp type) on a Z134 engine?

The Agcopartsbooks shows part number as 760001M2, but I can neither find a source nor information concerning this o-ring.

Thanks.
 
Back to top
View user's profile
miner09
Long Time User


Joined: 02 Dec 2009
Posts: 1377


Report to Moderator

PostPosted: Fri Dec 28, 2012 3:12 pm    Post subject: Re: Distributor O-ring for a TO-35 with Z134 engine Reply to specific post Reply with quote

You should be able to take it to a auto parts and fit a O-Ring. Mark position of rotor before removing it to keep in time.
 
Back to top
View user's profile
Checkptchickee
Regular


Joined: 30 Jan 2011
Posts: 20


Report to Moderator

PostPosted: Fri Dec 28, 2012 4:06 pm    Post subject: Re: Distributor O-ring for a TO-35 with Z134 engine Reply to specific post Reply with quote

Thanks Miner for the reply, but I bought the distributor on ebay a while back and it did not have the o-ring on it.

I guess I could get the ID to the distributor and the OD to the block, but should the o=ring have any overlap to the distributor housing and/or block?
 
Back to top
View user's profile
trac
Long Time User


Joined: 31 Oct 2009
Posts: 1365


Report to Moderator

PostPosted: Sat Dec 29, 2012 9:31 am    Post subject: Re: Distributor O-ring for a TO-35 with Z134 engine Reply to specific post Reply with quote

I've had mine out a few times and don't remember a over lap you should be fine
 
Back to top
View user's profile
Checkptchickee
Regular


Joined: 30 Jan 2011
Posts: 20


Report to Moderator

PostPosted: Sun Dec 30, 2012 7:43 pm    Post subject: Re: Distributor O-ring for a TO-35 with Z134 engine Reply to specific post Reply with quote

Thanks Trac. I will look at the setup more closely. Found another TO35 parts tractor this past weekend and am going to measure the o-ring on that one.

Thanks also to Miner for the help.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Harry Ferguson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters