|
This is the modern view of the Yesterday's Tractors Forums. Just login with your YT Userid and password to post. If you have trouble logging in, contact us by email to support at ytmag.com, or through the Reader Form, and we will get you going right away.
| View previous topic :: View next topic |
| Author |
Message |
jdman(MO)
Long Time User
Joined: 10 Dec 2001
Posts: 632
Report to Moderator
|
 Posted: Wed Jan 02, 2013 9:33 am Post subject: 70 block long stud |
  |
|
One stud in the 70 gas block is 3/8 inch longer than the others. I don"t think it goes where the parts books shows. I would think it goes where the oiler goes for the tappets. Russ
|
|
| Back to top |
|
 |
bigboreG
Regular
Joined: 07 Apr 2012
Posts: 431
Location: Lake View, IA
Report to Moderator
|
| Posted: Wed Jan 02, 2013 10:08 am Post subject: Re: 70 block long stud |
|
|
I would also think so too. I will check some info and post later.
|
|
| Back to top |
|
|
Fred from MO
Long Time User
Joined: 23 May 2004
Posts: 852
Report to Moderator
|
| Posted: Wed Jan 02, 2013 1:12 pm Post subject: Re: 70 block long stud |
|
|
I would think that it goes on the oiler as well, however your block studs may all not be run down in the block making some longer than the other.
|
|
| Back to top |
|
|
jdman(MO)
Long Time User
Joined: 10 Dec 2001
Posts: 632
Report to Moderator
|
| Posted: Wed Jan 02, 2013 2:09 pm Post subject: Re: 70 block long stud |
|
|
Fred one of the studs of 3/8 inch lomger. Russ
|
|
| Back to top |
|
|
Fred from MO
Long Time User
Joined: 23 May 2004
Posts: 852
Report to Moderator
|
| Posted: Wed Jan 02, 2013 3:41 pm Post subject: Re: 70 block long stud |
|
|
You would be surprised how tight they get going into yhe block.
|
|
| Back to top |
|
|
Machinery-Man
Tractor Expert
Joined: 21 Jan 2006
Posts: 1658
Report to Moderator
|
| Posted: Thu Jan 03, 2013 1:45 pm Post subject: Re: 70 block long stud |
|
|
The long case stud is for the oil feed casting. Fred the block studs are slightly oversize which results in a press or 0 clearance as they tighten into the case. I always used a pipe wrench and cheater to tighten, JD had a special tool for this, some lock up a couple of nuts to tighten in.
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
|
|
Discount Prices for Parts! You can help support this extensive website by purchasing your tractor parts, manuals and merchandise from our [ Antique Tractor Store ] or call our friendly sales staff toll free (800) 853-2651. [ More Info ]
|
YT Home
| Tractor Manuals
| Tractor Parts
| Forum Home
Copyright © 1997-2013 Yesterday's Tractor Co. - A Washington State Corporation
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
