Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

AG-6 steering brake


 
Post new topic    
View previous topic :: View next topic  
Author Message
Jeff Ziegler
Guest






Report to Moderator

PostPosted: Wed Jan 02, 2013 3:18 pm    Post subject: AG-6 steering brake Reply to specific post Reply with quote

I am looking to pickup a AG-6 that runs fine, just needs a fuel pump, for $1200. I am told it does not have steering clutches but uses the diff and brakes. I do not see any replacement brakes yet on the web? Are they not available anymore? I have also ready it does not make a good dozer, too high of gearing (1.78 mph in 1st), any truth to this? Some day I would like to put in a pond (1 acre, 5-8 ft deep), am I better off passing on this deal?
 
Back to top
J. Schwiebert
Guest






Report to Moderator

PostPosted: Wed Jan 02, 2013 3:34 pm    Post subject: Re: AG-6 steering brake Reply to specific post Reply with quote

It is your money. They do not have steering clutches (at least your AG-6 does not)Material for the bands is available, what will kill a set of bands real quick is using the wrong oil in the rear end.It probably is the easiest Cletrac engine to get parts for. How big a blade? Interesting here is that all the ponds around here are over 20 feet deep.
 
Back to top
george md
Tractor Expert


Joined: 22 Oct 2001
Posts: 2135
Location: Whiteford , Md

Report to Moderator

PostPosted: Thu Jan 03, 2013 9:08 pm    Post subject: Re: AG-6 steering brake Reply to specific post Reply with quote


Jeff,

I have an AG-6 with an HT-25 Heil 8 ft

trailbuilder , it will push that blade full.

This tractor has done many ponds and trench

silos. The last job I used it on was a 1.5

acre pond that had 10 ft stand pipe . Also

had 2 Case 1000's on the job 1 loader and

1 dozer with 10 ft blade. I still have all

of the tractors.

george
 
Back to top
View user's profile Visit poster's website
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Oliver, Cletrac, Coop and Cockshutt All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters