Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

1954 CA Water pump, Pulley removal


 
Post new topic    
View previous topic :: View next topic  
Author Message
Mark in WV
Regular


Joined: 13 Dec 2003
Posts: 70


Report to Moderator

PostPosted: Sat Jan 05, 2013 6:45 pm    Post subject: 1954 CA Water pump, Pulley removal Reply to specific post Reply with quote

Need to get a new pump for this tractor....Plan on buying a new one but cant get the pulley off to transfer it to a new one....I know its 2 separate flanges but I cant budge them...Any advice on how to remove them???
 
Back to top
View user's profile
chalmersbob(Pa)
Regular


Joined: 04 Jun 2009
Posts: 442


Report to Moderator

PostPosted: Sat Jan 05, 2013 7:41 pm    Post subject: Re: 1954 CA Water pump, Pulley removal Reply to specific post Reply with quote

Remove the 4 bolts on the front of the pulley and it will come off. It might need a little persausion, but that is all that holds it on. On the side of the pulley nose, the are 2 slots and 2 bolts sticking out with nuts on them. These are to set the width of the pulley groove. You don't have to do anything with them. They were originally there for tractors that didn't have a generator. They were used to tighten or loosen the belt on the pulley. LOL Bob
 
Back to top
View user's profile
Ted in NE-OH
Long Time User


Joined: 28 Nov 2012
Posts: 867
Location: Austinburg Ohio

Report to Moderator

PostPosted: Sat Jan 05, 2013 7:42 pm    Post subject: Re: 1954 CA Water pump, Pulley removal Reply to specific post Reply with quote

Once the 4 bolts that hold the fan are out the pulley should come off with no further disassemble. Do not have to separate halves of pulley as it won"t gain you anything.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters