Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

generator


 
Post new topic    
View previous topic :: View next topic  
Author Message
beaubeau
New User


Joined: 14 Jan 2013
Posts: 1


Report to Moderator

PostPosted: Mon Jan 14, 2013 3:48 am    Post subject: generator Reply to specific post Reply with quote

how to field the generator to get it to charge?
 
Back to top
View user's profile
Bruce (VA)
Tractor Guru


Joined: 24 Feb 2003
Posts: 12938
Location: Old Church VA

Report to Moderator

PostPosted: Mon Jan 14, 2013 5:25 am    Post subject: Re: generator Reply to specific post Reply with quote

I'm not sure I understand your question.

If you are asking how to polarize the generator, see tip # 23.

If you are trying to troubleshoot a 'no charge' problem, check out the flow chart.

75 Tips

 
Back to top
View user's profile Visit poster's website
Mr. T. Minnesota
Regular


Joined: 17 Jan 2012
Posts: 477


Report to Moderator

PostPosted: Mon Jan 14, 2013 5:28 am    Post subject: Re: generator Reply to specific post Reply with quote

BB,
What is the generator on? What are you attempting to do? If there is a field, must be a later version.
Mr. T. Minnesota
 
Back to top
View user's profile
souNdguy
Tractor Guru


Joined: 20 Aug 2002
Posts: 54058


Report to Moderator

PostPosted: Mon Jan 14, 2013 6:52 am    Post subject: Re: generator Reply to specific post Reply with quote

initial polerization of

a circuit: jump bat to arm

b circuit: jump field to bat


how to full field to test a genny output:

a circuit: jump field to ground

b circuit: jump field to bat

how to motor test, belt off:

a circuit: jump bat to arm and field to ground

b circuit: jump bat to arm and field
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Ford 9N, 2N, 8N All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters