Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

to30


 
Post new topic    
View previous topic :: View next topic  
Author Message
dennis gallagher
New User


Joined: 14 Jan 2013
Posts: 5


Report to Moderator

PostPosted: Mon Jan 14, 2013 7:45 am    Post subject: to30 Reply to specific post Reply with quote

can anyone tell me if a hydralic control quadrant from an 8n tractor fit on a to30 tractor
 
Back to top
View user's profile
old
Tractor Guru


Joined: 12 Mar 2000
Posts: 56193
Location: Lake of the Ozarks area of MO

Report to Moderator

PostPosted: Mon Jan 14, 2013 9:33 am    Post subject: Re: to30 Reply to specific post Reply with quote

I do not think so. While to 2 look to be very close to the same machine they are no where near close to being the same
 
Back to top
View user's profile
Jerry/MT
Tractor Guru


Joined: 22 Jul 2003
Posts: 10081
Location: Western Montana

Report to Moderator

PostPosted: Mon Jan 14, 2013 1:19 pm    Post subject: Re: to30 Reply to specific post Reply with quote

A 2N or a 9N will. It"s the same system.
 
Back to top
View user's profile
dennis gallagher
New User


Joined: 14 Jan 2013
Posts: 5


Report to Moderator

PostPosted: Tue Jan 15, 2013 8:41 am    Post subject: Re: to30 Reply to specific post Reply with quote

thanks i thought it was
 
Back to top
View user's profile
old
Tractor Guru


Joined: 12 Mar 2000
Posts: 56193
Location: Lake of the Ozarks area of MO

Report to Moderator

PostPosted: Tue Jan 15, 2013 8:54 am    Post subject: Re: to30 Reply to specific post Reply with quote

Just remember he said 9N/2N but he did not say the 8N like you asked. Has to do with the 8N having position control and the Ferguson's did not and the 9N/2N did not either
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Restoration and Repair Tips All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters