Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

SA Seal Problem


 
Post new topic    
View previous topic :: View next topic  
Author Message
Doug Kieta
Regular


Joined: 15 Feb 2012
Posts: 49


Report to Moderator

PostPosted: Tue Jan 15, 2013 6:13 pm    Post subject: SA Seal Problem Reply to specific post Reply with quote

Does anyone have a valid cross-oover number for SA part #51-494-DA. This is the oil seal for the differential shaft on a SA. I went to our local IH dealer today who said he had two of them. However, when I got there, the seal he showed me that had this part number was significantly larger in diameter than the one that came out of my tractor. The old seal is a National #410060-SSR. I also tried our local bearing distributor and he was unable to cross the National number into a modern seal. I also tried NAPA. They were able to cross the number but the seal they came up with was also much larger in diameter than my original.

I am dead in the water until I can find this seal. Any help you guys can offer will really be appreciated.

Thanks.
 
Back to top
View user's profile
CNKS
Tractor Guru


Joined: 10 Mar 2002
Posts: 18555


Report to Moderator

PostPosted: Tue Jan 15, 2013 6:27 pm    Post subject: Re: SA Seal Problem Reply to specific post Reply with quote

I replaced all the seals in my Super A, either the IH ones or ones crossed to SKF (Chicago Rawhide). They are all available. But, 51494 DA interchanges with 358786 R91 and 358825 R91, ask your dealer to order one of those or cross it to National or SKF.
 
Back to top
View user's profile
pete 23
Tractor Guru


Joined: 10 Sep 2009
Posts: 6478


Report to Moderator

PostPosted: Tue Jan 15, 2013 6:38 pm    Post subject: Re: SA Seal Problem Reply to specific post Reply with quote

Are you sure the old seal was not a double seal inside of an outer seal cage. That is what is on all H am M farmalls and a lot of guys dig them out and say, new one is too large when in reality they are correct because they left the old seal cage in.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters