Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

4020 injector pump


 
Post new topic    
View previous topic :: View next topic  
Author Message
davida
Regular


Joined: 23 Aug 2007
Posts: 142


Report to Moderator

PostPosted: Wed Jan 23, 2013 9:58 am    Post subject: 4020 injector pump Reply to specific post Reply with quote

Where can I find a manual that covers a Roosa Master DBG VC633-3AJ pump? I have had it apart and I am not sure were a few of the parts go.

I can find the manuals that cover the second generation but not this older one.

Thank you for any help.
 
Back to top
View user's profile
tim s
Tractor Guru


Joined: 01 Nov 2008
Posts: 7223
Location: Somerset Ohio

Report to Moderator

PostPosted: Wed Jan 23, 2013 11:32 am    Post subject: Re: 4020 injector pump Reply to specific post Reply with quote

Ljd can help you with that,,but I haven't seen him on here for a while...
 
Back to top
View user's profile
Dieseltech
Long Time User


Joined: 29 Feb 2012
Posts: 1346


Report to Moderator

PostPosted: Wed Jan 23, 2013 11:47 am    Post subject: Re: 4020 injector pump Reply to specific post Reply with quote

What do you need to know? Will not be home tonight til late, but if you like call after 7 PM IN time, five seven four eight nine three four one seven two. Ask for Rich.
 
Back to top
View user's profile
davida
Regular


Joined: 23 Aug 2007
Posts: 142


Report to Moderator

PostPosted: Wed Jan 23, 2013 11:55 am    Post subject: Re: 4020 injector pump Reply to specific post Reply with quote

Main questions are there are 2 steel rods that go in the head assembly.

Where does the short one go?

What directions does the long one go, with the plunger type end toward or away from the plug?

I took it to far apart and these parts fell out before I knew they were there.
 
Back to top
View user's profile
Dieseltech
Long Time User


Joined: 29 Feb 2012
Posts: 1346


Report to Moderator

PostPosted: Wed Jan 23, 2013 12:01 pm    Post subject: Re: 4020 injector pump Reply to specific post Reply with quote

Smaller vent wire goes in bore first. Longer goes next, one end is larger due to normal wear, grind edge down or install with peaned end next to retaining plug.
 
Back to top
View user's profile
davida
Regular


Joined: 23 Aug 2007
Posts: 142


Report to Moderator

PostPosted: Wed Jan 23, 2013 12:05 pm    Post subject: Re: 4020 injector pump Reply to specific post Reply with quote

Thank you, I thought I have tried to install them both in the same bore with not luck but I will try again.
 
Back to top
View user's profile
Dieseltech
Long Time User


Joined: 29 Feb 2012
Posts: 1346


Report to Moderator

PostPosted: Wed Jan 23, 2013 12:24 pm    Post subject: Re: 4020 injector pump Reply to specific post Reply with quote

Glad to help. Have been repairing pumps since 1976. Will be home tomorrow nite, call if you like.
 
Back to top
View user's profile
davida
Regular


Joined: 23 Aug 2007
Posts: 142


Report to Moderator

PostPosted: Thu Jan 24, 2013 10:22 am    Post subject: Re: 4020 injector pump Reply to specific post Reply with quote

One last question...maybe.

Is there a part number for the housing or fitting that makes up the pressure regulator sleeve assembly?

The one I have has been broken off at the top.
 
Back to top
View user's profile
Dieseltech
Long Time User


Joined: 29 Feb 2012
Posts: 1346


Report to Moderator

PostPosted: Thu Jan 24, 2013 10:46 am    Post subject: Re: 4020 injector pump Reply to specific post Reply with quote

Transfer cap regulating sleeve, 17058 old #, new # 27917.
 
Back to top
View user's profile
davida
Regular


Joined: 23 Aug 2007
Posts: 142


Report to Moderator

PostPosted: Thu Jan 24, 2013 11:17 am    Post subject: Re: 4020 injector pump Reply to specific post Reply with quote

Thank you, are these JD numbers?
 
Back to top
View user's profile
Dieseltech
Long Time User


Joined: 29 Feb 2012
Posts: 1346


Report to Moderator

PostPosted: Thu Jan 24, 2013 11:32 am    Post subject: Re: 4020 injector pump Reply to specific post Reply with quote

These are Stanadyne #s.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> John Deere All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters