Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Rotar removal on Farmall 140


 
Post new topic    
View previous topic :: View next topic  
Author Message
John D. H
Guest






Report to Moderator

PostPosted: Fri Jan 25, 2013 10:09 am    Post subject: Rotar removal on Farmall 140 Reply to specific post Reply with quote

Hi, I have a question. I have a IH Farmall 140 which I am repairing. I have taken the distributor cap off, but I can't remove the rotar. I pull on it quite hard, but it feels like there is a clip holding it on behind it. Is this true or does it need oil? How Do I remove the rotar? Is there a diagram?
 
Back to top
mkirsch
Tractor Guru


Joined: 08 Oct 2007
Posts: 10872


Report to Moderator

PostPosted: Fri Jan 25, 2013 10:43 am    Post subject: Re: Rotar removal on Farmall 140 Reply to specific post Reply with quote

There is nothing special holding the rotor on. Just pull harder. Sometimes they stick if they've been on there a long time.

NO OIL.
 
Back to top
View user's profile
El Toro
Tractor Guru


Joined: 04 Jun 2004
Posts: 22368


Report to Moderator

PostPosted: Fri Jan 25, 2013 10:44 am    Post subject: Re: Rotar removal on Farmall 140 Reply to specific post Reply with quote

You don't need oil on a rotor. I wouldn't pull it unless it's damaged. Hal
 
Back to top
View user's profile
Jim Becker
Tractor Guru


Joined: 15 Jan 1998
Posts: 3705
Location: MN

Report to Moderator

PostPosted: Fri Jan 25, 2013 11:39 am    Post subject: Re: Rotar removal on Farmall 140 Reply to specific post Reply with quote

The rotor shaft is hollow with an oil wick in the center. It should get a drop of oil once in a while. Since your rotor is firmly stuck, your wick probably has't had any oil lately.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters