Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Need help finding an O ring for 300 IPTO


 
Post new topic    
View previous topic :: View next topic  
Author Message
Zachary Hoyt
Tractor Guru


Joined: 07 Aug 2008
Posts: 3922


Report to Moderator

PostPosted: Sat Jan 26, 2013 2:04 pm    Post subject: Need help finding an O ring for 300 IPTO Reply to specific post Reply with quote

I finally got back to work on the 300 today since the high temp finally got all the way back up to 17. While putting the IPTO back in I broke a piece out of the O ring looking thing that seals between the outside of the housing and the rear end case. I am not 100% sure that it is an O ring, but that is my best guess. It is about 6 inches in diameter at a guess. I have been searching for a new one online and have not been able to come up with anything. If anyone knows where I can get one or how to cross reference it to a part number or a proper name for what it is so that I could get it from a generic supplier I would appreciate any information. Thank you very much.
Zach
 
Back to top
View user's profile
D Slater
Tractor Guru


Joined: 30 Jul 2007
Posts: 3994


Report to Moderator

PostPosted: Sat Jan 26, 2013 3:16 pm    Post subject: Re: Need help finding an O ring for 300 IPTO Reply to specific post Reply with quote

Seal ring 384398R1 that is sold by dealers is not round all the way around. Cost 13 dollars and change at some, shipping on that if needed.
Used to get round ones from a industrial rubber supplier near me that would work. That business is gone like a lot of others now. Probably wouldn't be much cheeper than the dealer by now if they were.
Zach, just checked Messicks and they say $13.48.
 


Last edited by D Slater on Sat Jan 26, 2013 3:20 pm; edited 1 time in total
Back to top
View user's profile
Zachary Hoyt
Tractor Guru


Joined: 07 Aug 2008
Posts: 3922


Report to Moderator

PostPosted: Sat Jan 26, 2013 3:57 pm    Post subject: Re: Need help finding an O ring for 300 IPTO Reply to specific post Reply with quote

Thanks a lot, I should have thought to check messicks. Thanks a lot for the parts and advice. I put the new countershaft gear and ring gear in today and will be meshing the new ring gear tomorrow, I think.
Zach
 
Back to top
View user's profile
Tom Fleming
Tractor Expert


Joined: 06 Jun 2007
Posts: 2421
Location: pennsylvania

Report to Moderator

PostPosted: Sat Jan 26, 2013 4:32 pm    Post subject: Re: Need help finding an O ring for 300 IPTO Reply to specific post Reply with quote

If you have the dimensions, try Graingers. Joe's farmall MAY have it.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters