Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

super c


 
Post new topic    
View previous topic :: View next topic  
Author Message
cchigg
Regular


Joined: 17 Oct 2012
Posts: 20


Report to Moderator

PostPosted: Fri Feb 08, 2013 4:51 pm    Post subject: super c Reply to specific post Reply with quote

anyone know if the axel key slot is straight cut or has a taper to it on a super ? I am putting 9 bolt hubs oh that has a 3/4 "key so I have to have a step key made to accept the 1/2" axel. Thank for any help.
 
Back to top
View user's profile
Joshua Rod
Regular


Joined: 05 Mar 2012
Posts: 277
Location: Rural Clearwater, Mn

Report to Moderator

PostPosted: Fri Feb 08, 2013 6:24 pm    Post subject: Re: super c Reply to specific post Reply with quote

I believe it to be straight. That way you can slide the wheels in/out for adjusting wheelspacing.
 
Back to top
View user's profile
504
Tractor Guru


Joined: 14 Jun 2005
Posts: 5045


Report to Moderator

PostPosted: Fri Feb 08, 2013 7:34 pm    Post subject: Re: super c Reply to specific post Reply with quote

Yes, straight.
 
Back to top
View user's profile
BBinOk
Regular


Joined: 22 Sep 2011
Posts: 37


Report to Moderator

PostPosted: Sun Feb 10, 2013 5:20 am    Post subject: Re: super c Reply to specific post Reply with quote

I just did the same thing to my super .Went from 3/4 to 1/2 keyway and it does have a slight taper to it.
 
Back to top
View user's profile
whigg
Regular


Joined: 11 Jul 2012
Posts: 132


Report to Moderator

PostPosted: Sun Feb 10, 2013 1:37 pm    Post subject: Re: super c Reply to specific post Reply with quote

Thanks for the replys. I don't have the tractor home yet but trying to get things ready for the pulling season.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters