Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

7045 rear PTo seal leaking


 
Post new topic    
View previous topic :: View next topic  
Author Message
TLZ
Regular


Joined: 17 Nov 2011
Posts: 40


Report to Moderator

PostPosted: Sat Feb 16, 2013 12:11 pm    Post subject: 7045 rear PTo seal leaking Reply to specific post Reply with quote

How do u change the rear PTo seal on a 7045? My friends
tractor started leaking this fall, it is dripping oil when not in use.
Todd. Thanks
 
Back to top
View user's profile
gearheadbill
Regular


Joined: 12 Aug 2012
Posts: 62


Report to Moderator

PostPosted: Sun Feb 17, 2013 6:53 am    Post subject: Re: 7045 rear PTo seal leaking Reply to specific post Reply with quote

Chances are it is a 2 speed, 540/1000. You will have to drain rear end oil, remove plate on underside of PTO, and this will expose shaft and gears. These will have to be removed to replace the seal. It needs to be set back up to proper pre-load on bearings. Kind of tricky reinstalling gears and setting up.
 
Back to top
View user's profile
CameronKabe
New User


Joined: 30 May 2013
Posts: 1


Report to Moderator

PostPosted: Thu May 30, 2013 5:55 pm    Post subject: Re: 7045 rear PTo seal leaking Reply to specific post Reply with quote

This is my first year farming, I'm using my fathers equipment and the same thing happened on the 7045 im using. I have managed to pull the lock pin out of the nut on the shaft holding the gears in place but I can seem to get the barring off the end of the shaft in order to slide the shaft out. Does that barring just need to be driven off the shaft or is there a snap ring I'm just not seeing in place somewhere? Ive tried looking all over it with mirrors and I have the parts diagram but i'm afraid of braking something. Please Help!!!
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters