Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

almost done finally


 
Post new topic    
View previous topic :: View next topic  
Author Message
Travis M
Regular


Joined: 14 Jan 2013
Posts: 238


Report to Moderator

PostPosted: Sun Feb 24, 2013 5:11 pm    Post subject: almost done finally Reply to specific post Reply with quote

99 percent done finally. We only have a few small things to finish up. We could pull today if we need to.


 
Back to top
View user's profile
ss409
Regular


Joined: 07 Dec 2012
Posts: 110


Report to Moderator

PostPosted: Sun Feb 24, 2013 5:19 pm    Post subject: Re: almost done finally Reply to specific post Reply with quote

reminds me of an old smoker tractor from bout 25yrs ago,, It was called The Pouncer. mite have been a 700,730 model,, itd take him a minute to lite the fires at the line,,, it would take off n smoke a blowin n a 8in tall blow torch looking flame out the pipe on a late night would always be visable. same patina on it too! lol.
 
Back to top
View user's profile
Travis M
Regular


Joined: 14 Jan 2013
Posts: 238


Report to Moderator

PostPosted: Sun Feb 24, 2013 5:22 pm    Post subject: Re: almost done finally Reply to specific post Reply with quote

I think the patina is gonna be there for a season. We like to pull them a season, fix all the leaks then paint. I like working on them, but I am so ready for this project to be done.
 
Back to top
View user's profile
north puller
Long Time User


Joined: 05 Jan 2010
Posts: 961


Report to Moderator

PostPosted: Sun Feb 24, 2013 6:37 pm    Post subject: Re: almost done finally Reply to specific post Reply with quote

Travis, has the motor seen some break in time? Have you dyno tuned it? HP numbers look good? What RPM are you gonna turn?
 
Back to top
View user's profile
Travis M
Regular


Joined: 14 Jan 2013
Posts: 238


Report to Moderator

PostPosted: Sun Feb 24, 2013 7:37 pm    Post subject: Re: almost done finally Reply to specific post Reply with quote

It has some break in time on it, no pto so no dyno time. Its gonna have to be a run and tune deal. Not gonna run it over 2000 rpms for the most part. If we get a steel flywheel it can run up to 3000 safely.
 
Back to top
View user's profile
bigmo
New User


Joined: 24 Feb 2013
Posts: 7


Report to Moderator

PostPosted: Sun Feb 24, 2013 11:56 pm    Post subject: Re: almost done finally Reply to specific post Reply with quote

Looking good! from what you have posted she should make some big horsepower. Can't wait to see a video of it pulling if u get a chance.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Pulling All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters