(800) 853-2651
SHOP NOW

Search results

  1. J

    2555 Parking Brake

    Had to change out the parking brake band on my 2555. The issue I'm having is as I tighten up the adjusting screw Key#4 to set my band adjustment the end of the screw is being forced into the end of the band lining before the band tightens up and I can't get it adjusted properly. Im sure I have...
  2. J

    JD 127 Gyramoor Slip Clutch

    We have a 127 and rebuilt it a number of years ago. If I remember right that's a large Belleville washer behind the nut. You have it flattened out by the look of it in the picture so I would suspect you need clutches. Not cheap to replace but I'm not sure you can buy a new rotary cutter built...
  3. J

    Powerquad Forward Cluch Problem

    Okay thanks for your help.
  4. J

    Powerquad Forward Cluch Problem

    Gotcha now I see what you're getting at. Am I correct in thinking a problem with the cooler relief or lube relief valve would affect system pressure? And would therefore affect reverse brake pressure also?
  5. J

    Powerquad Forward Cluch Problem

    80 psi on forward clutch test port 205 psi on reverse brake port. Didn't check system pressure as reverse brake pressure was at 205 so I assumed system pressure was good. Lube pressure recovered on both forward and reverse shift as per manual however on the forward shift the pressure drop was...
  6. J

    Powerquad Forward Cluch Problem

    Electric reverser the shift solenoids and shift valves have been interchanged forward to reverse problem remains on the forward side. My understanding is the enable proportion solenoid pulses the apply oil to gradually apply oil pressure to shift valve. If it was the issue shouldn't I have...
  7. J

    Powerquad Forward Cluch Problem

    Lube pressure checks out when you shift to reverse drops and then gradually recovers as it routes cooling oil to brake. In forward there is a bigger pressure drop and it takes longer to recover. What do you mean by modulation valves?
  8. J

    Powerquad Forward Cluch Problem

    Have a 2002 6420 with a Powerquad 24 speed that lost forward clutch pressure baling 2nd cut late last summer. Should have 205 psi had 80 psi. Reverse had 205 worked fine all 1-2-3-4 shifts worked fine. Pulled transmission this winter rebuilt forward clutch, all new seals, all new gaskets, oil...
  9. J

    Books,manuals

    Never understood the reluctance to buy a manual. Some leave a lot to be desired but I run mostly Deere equipment their manuals are well written, and they even sell manuals to explain theory of operation if you don't get it from studying it. I'm in the process of putting a Powerquad back in a...
  10. J

    harveststore silo ?

    An excellent commentary that extends to many other things in life besides silos and equipment.
  11. J

    John Deere 336

    Probably needs some attention but that number is possible. Grandfather bought a 336 new in 1973 and conservatively has baled 400000+. If it's been stored inside that's a plus.
  12. J

    Best chainsaw.

    I have a 261 about 4 years now. It's the smallest pro saw. If you can wait you wont regret it nice saw. Keep fresh gas in it and run the good Stihl chain oil and you're good to go. If you can beg, borrow or steal until it arrives you won't be sorry.
  13. J

    Kingdom gets a pup

    Looks like a Bart to me. Have a female red heeler, in one word tenacious.
  14. J

    JD 336 Baler Kicker

    Are you breaking shear bolts with the plunger safety stop or are they breaking after a period of use (ie you bale for a while and then you notice the feeder fork is acting erratic, you turn the PTO off and the bolt is sheared)? If the latter, install a shear bolt and before tightening rock the...
  15. J

    JD seat sag.

    If it has a Grammer seat also check there are nylon rollers that wear over time and cause everything to cock sideways and bind everything up when you sit on it changing them at the same time will make a big difference too. If I remember correctly there are four in the back vertical suspension...
  16. J

    How long to wear paint of baler needles

    RayP is right. Plungerhead holds hay in compression as needles bring twine to knotters on tie cycle. It's not like the needle in a sewing machine or bag closer.
  17. J

    336 baler year

    FWIW my grandfather bought #133728 in the summer of 1973.
  18. J

    328 John Deere baler repair

    Your knives are likely gouged and catching as they pass each other. And if it snuffed the tractor your slip clutch is either too tight or rusted up it should have slipped and not stalled the tractor.
  19. J

    PTO Shaft

    Unhook the rake then slowly drive ahead until the halves come apart and try taking it off then. That usually works.
  20. J

    329 Valve Lash Adjusters

    Tim I'm running short of power cutting hay and I'm trying to sort it out. Usually cut in C1 and I'm down into A4 after an hour or two cutting. Thought at first it was heavier hay that was down but I opened the cab door and noticed a miss in the exhaust note. About 2000 hours since rebuild. Laser...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top