(800) 853-2651
SHOP NOW

Search results

  1. F

    Combine bin cover

    Combines sold in SA have a tarp grain bin cover, because harvest is done during short storms, and it is common there to harvest the end of one field, while rain is pouring on the other side. Here in Europe, Massey 700 series had tarp covers with a steel structure. 800 series had a steel...
  2. F

    1963 4010 wide front question

    As usual, 1/10th of a turn before breakage.
  3. F

    4440 wedge beater pipe

    It wouldbe much easier to answer same question in metric system. Pipe 114mm 10thick fits over the 92mm axle.
  4. F

    Best way to get a stuck engine loose

    You can pour rust remover (cheap stuff you mix with water, sold at walmart). Work pretty good and cleans the rust.
  5. F

    3 Point Without Draft Parts

    For sure yes, the 760a was even sold with a straight pto, per jdparts.. 4 years ago, I bought a shaft frem wengers labelled as the correct shaft for the straight 1000rpm pto. But upon receiving it, it was simply a regular shaft for the gearbox. I explained above the idea of using the 760a shaft...
  6. F

    3 Point Without Draft Parts

    On mine,i measured 19'' center to center on.both trans and 16'' wide. Also, the plug R30819 is the same on both tractors (760a and 5020) and diameter is same as r26505 bushing. It is odd, that, so close, it does not work. For the drawbar, the bosses are in the transcase, so i will drill and...
  7. F

    3 Point Without Draft Parts

    I went out and remesured this morning. For the transmission filter base, practical and clean location would be under the RH toolbox, with the filters facing forward and the hydraulic pipes facing up, and the filter base slighthly "inside" the toolbox. (so filters are not too low, odd looking...
  8. F

    3 Point Without Draft Parts

    Seems like you are making more progress than me. There are rockshaft passages and bosses to.install the three point draft control.it looks like a hole in the rockshaft cover needs to be made for the disconnect. It will be accessible from the oil gauge door. Also, putting scraper finals on a...
  9. F

    Front end swap

    Not sure that it has been repaired. The welds always looks very big, andnot very smooth n those axles. This washefore robotic welding. Most repairs involve an extra welded gusset
  10. F

    ‘68 4020 Syncro

    Also, I am holding the nuts with a good tongue and groove pliers.
  11. F

    ‘68 4020 Syncro

    If your nuts that lay at the bottom of the trans move forward, they will go in the pto gears. You need to take them off. As far asputting the nut on, It ismuch easier if you have the forks removed. Otherwise, you can use a rag (like an old tee shirt),to fill the void around the nut, and not...
  12. F

    ‘64 JD 4020 syncro

    You need to have the shifter cam in the lowest position, and the shifter can come off. No need to remove the shifter cam.
  13. F

    4020 style power steering upgrade

    Same setup as late john deere 500c and 510 backhoe.
  14. F

    update on 3020 gas starting issues

    The other carb is a zenith, around $600 new.
  15. F

    Dealer Service Dept. Slide Shows....

    Thank you very much for posting this. I really like the one about the 15 speeds.
  16. F

    G707 tach drive diesel

    Thank you for the info.
  17. F

    G707 tach drive diesel

    Thank you for the info. I cannot find parts numbers or pictures in the tractors before the G707. Are you sure some GVI diesels came from factory with a tach? Do you have pictures?
  18. F

    4640 Hydraulic Noise

    Many tractors with the cl9sed center system are doing this. Very normal. If you can lower and raise the three point few times at low idle without having the hree point chatter, your tractor is fine.
  19. F

    2040 Top Dead Center -visible at flywheel??

    The bigger hole is for the rotator tool. You need to insert a pin (5/16 screw) in the cover plate attaching bolt hole and turn the motor untul it drops in the hole.
  20. F

    5445 Fuel tank

    There should be a port to connect the right tank to an optional left tank with a big hose and pipe, under the tractor.
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top