Search results

  1. D

    super 55 pto

    Yes, there is two allen screws holding the clutch pack. The short one is to lock the longer one. Hard to get to slide off with removing just one. Don't ask how I know.
  2. D

    Oliver 550 front axle pin

    Any suggestions on how to drive out the front axle pivot pin on a Oliver 550? It appears it has to come forward. Kent, I am sure you have done one or two.
  3. D

    Question for Dieseltech or others

    I tried a new fitting with the ball inside and it did a little better but continued to die. I punched the ball out of the old one, put it back in and all is well. I was told you can not get one with a bigger orifice and check ball. I have to say, I almost lost my religion on this ordeal. Thanks...
  4. D

    Question for Dieseltech or others

    My tank was cleaned by a professional. Good flow to prime. Started right up then died. I loosened the cover on the pump and it would prevent it from dying. I removed all the return lines and blew air through them and the T's. Fired right up. Went to wash my hands and it died. I am at a loss. I...
  5. D

    Question for Dieseltech or others

    Thank you Dieseltech. The tank is out of the tractor and going to be cleaned out. I will check the filter upon bleeding system.
  6. D

    Question for Dieseltech or others

    I have a rebuilt 1555 diesel. Pump was gone through by professional that is now retired about 8 years ago. It would ocassionally die from fuel starvation. Found a plastic gas jug cap floating in tank that I assumed got pulled down on Strainer assembly. Thought problem was fixed. After sitting...
  7. D

    carburetor

    I have a 1650 I purchased for the fenders. Guess I will part the rest out.I do not know if it will work. I can get the TSX number off of it. Also has a replaced Mallory distributor. Duane 812-six three nine 6536.
  8. D

    Gresen 2 spool valve. Oliver power beyond

    It is a model 2702. It came off an Oliver 550. There was a plug in one of the cylinder ports and an exhaust hose on the bottom.That is the cylinder port that I can't blow air through. I plugged the bottom and put an elbow where the plug was. My number is 812-639-6536. Thanks again John!
  9. D

    Gresen 2 spool valve. Oliver power beyond

    I'm going power beyond on my 1550 Oliver. I have a open center two spool valve off an old Oliver. On the bucket tilt spool, when I blow air in the inlet air only comes out one of the openings with the handle pulled or pushed but nothing with the handle the other direction. The lift ports work...
  10. D

    How can I tell if my 1550 has the "high speed reare

    My 1550 & 1555 utilities have a high speed. That code is -506.
  11. D

    310 Waukesha

    I thought the newer ones had the oil pressure set and relief on the pump itself. I had a block from a 2-70 that way in my 1655. Correct me if I'm wrong.
  12. D

    Oliver 550

    I'm not saying it is not possible but I have never seen one with a crack. Likely needs seals replaced by brake pedal shaft or by pto clutch.
  13. D

    Oliver 550 steering cylinders

    Dear Kent Gordon or others, What is the answer to replacing 550 Oliver power steering cylinders? Thanks for the replies.
  14. D

    1650 Oil Leak

    I bought a brand new one not too many years ago. I believe Maibach's or AJ Boellner.
  15. D

    Oliver 550 clutch release resolved

    after split the drive clutch would not release. John Schweibert knew exactly what we figured out! I was a little rough putting the two halves together and bowed the pressure plate.I am getting better after splitting it four times trying to figure it out. John we thank you for all your help and...
  16. D

    Oliver 550 clutch release

    Thanks. I will check that.
  17. D

    Oliver 550 clutch release

    No I did not change rear engine seal.All the other seals I replaced. Pointed end goes towards front of tractor. Am I correct?
  18. D

    Oliver 550 clutch release

    It went together fine. The pto engages and disengages as it should. The engine drive clutch is what doesn't release. I am confused!!
  19. D

    Oliver 550 clutch release

    Very nice well done video. Where did you get the clutch alignment tool?
  20. D

    Oliver 550 clutch release

    I tried to reverse it after second split but that put it in a way off position. It is as it appears in parts book.

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top