(800) 853-2651
SHOP NOW

Search results

  1. A

    1953 ford jubilee 3 point hitch not working

    It's O.K. to use the hose technique to bleed the pump as long as it's removed and plugged before further testing. I looked at your videos, one appears to have flow in the relief valve area, I don't think that should be the case during normal functioning. There's a YT member JMOR that has...
  2. A

    1953 ford jubilee 3 point hitch not working

    In your picture you have your pump pressure port redirecting pump output back to the sump. You won't develop any pressure that way, put the plug back in.
  3. A

    Making your own Hydraulic Hoses

    They are the right diameter, thickness, and material as the crimp section of common fittings, at least for Weatherhead U-Series, so I have used them to crimp new hose onto old, odd, unobtainable fittings. It's not ideal but it has worked for me.
  4. A

    Making your own Hydraulic Hoses

    I get mine from Discount Hydraulic Hose, they call them crimp collars (I think that's what you're looking for anyway). Crimp Collars
  5. A

    Making your own Hydraulic Hoses

    I have the economy option, a Weatherhead shop press kit with dies from 1/4" to 1". It uses my manual 30 ton shop press with a pusher, die ring and die. It uses standard two wire SAE hydraulic hose and U-Series ends. The selection of ends is fairly vast, both Wearherhead and clone. When I...
  6. A

    Ford 860 Axle Pin Assembly Bolt Spec

    It's from the parts book shown below. Most of the diagrams/parts info are replicated online at CNH and Messicks.
  7. A

    Ford 860 Axle Pin Assembly Bolt Spec

    Does this diagram have the info you're looking for?
  8. A

    Ford 800

    The Ford Parts manual shows pistons are the same for gas and LPG, see #30.
  9. A

    1953 ford jubilee 3 point hitch not working

    Below is what I&T says about pressure test points (as described for a different test), or you could use the plug on the piston pump as George pointed out. Since you apparently not developing any high pressure, only back pressure, you could use a lower pressure gage for a more accurate measurement.
  10. A

    1953 ford jubilee 3 point hitch not working

    Take a pressure reading and if backpressure is 40-45 PSI or so it's working. This is done with lift cover in place.
  11. A

    1953 ford jubilee 3 point hitch not working

    Definitely check the backpressure valve. Unlike later models it's not built into the lift cover but rather in the center housing. You can check by taking a pressure reading under conditions outlined below, should be 40-45 PSI. I assume you have service manual(s), this from I&T FO-19.
  12. A

    3-point arms on Ford 641 lifting but not dropping

    When that happened to me it was a stuck unloading valve. Probably time to pull the lift cover, inspect linkages and valving, refresh seals and O-rings and adjust.
  13. A

    Dynahoe 490

    I found my original brochure. Weight difference is because 20720 lb weight for the 190-4 doesn't include weight of cab.
  14. A

    Dynahoe 490

    Since the 490 was basically an updated 190-4 here is a brochure page for the 190-4. It should give you an idea. Front bucket and shipping width was 8 foot. The 490 seems to be a couple tons heavier, I don't know where the weight gain was. Also a link to a sold 490 on Bigiron, has some good...
  15. A

    NAA losing prime and air bubbles in the hydraulic fluid

    Quite a while ago there was someone on this board with the same symptoms. He had replaced the suction line with a new one. After a lot of frustration he finally discovered a porous weld and tigged it to fix the problem. I guess the moral of the story is to carefully check the suction tube for...
  16. A

    ford backhoe loader

    KD4 at beginning of model number means 445A. Unit code 6C17B is March 17 1986 day shift. Serial number C757800 is a 1986 number, C is made in USA.
  17. A

    Ford 600 hood hardware

    I think the parts diagram is incomplete. My printed Parts List 1953/64 has the same diagram. I'm afraid if you found an earlier one the hardware would go by part number not dimensions. I checked my tractor and found I was missing some of the nuts and bolts you are looking for. Maybe someone...
  18. A

    Ford 600 hood hardware

    Here's a diagram/parts list that's a bit easier to use. Fasteners are mostly "Procure Locally" Messicks 600 Sheet Metal
  19. A

    Decoding Ford Industrial Casting Code

    If you search the web for D3JL6015J it overwhelmingly comes up as a 172 suitable for 800/801/4000 4 cylinder tractors. Try the search, lots of comments from respected old-time YT members.
  20. A

    Length of Tach/Proof Meter cable for Jubilee/NAA

    Apparently there was a cable assembly for the NAA prior to the one listed for '53 forward. It's part number is FAD-17365-A instead of B9NN-17365-B. Go to Ebay and search for item 293737936754 to take a look. Carefully read parts diagram item 5. The used one on Ebay doesn't give a length, you...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top