(800) 853-2651
SHOP NOW

Search results

  1. R

    A/C CA Cutch/gear slipping

    Right on, I’ll give that a whirl tomorrow evening when I do chores again. Are parts relatively available for these tractors?
  2. R

    A/C CA Cutch/gear slipping

    I was just recently given an Allis Chalmers CA. I don’t exactly know the year as my neighbor just dropped it off. I used it today to pull around a green chop feeder to put hay in for the cows and noticed it drove beautifully out to the wagon but I put it in reverse it didn’t move. I put it back...
  3. R

    New Holland 461 wobble box

    I am in search of a wobble box assembly or at the minimum the main pulley that the wobble shaft if fixed too. I had a bearing failure last year and it shewed the shaft up and was curious if anyone might have an old haybine laying around they would sell it for. I was planing to take it off and...
  4. R

    John Deere 30 Ejector

    Just some preliminary checks what is the condition of the belts on the side? Is the tension set properly? Also are the arms coming back at all or just staying fully extended. If they are coming back and just not latching there could be some other issues going on than what listed above but from...
  5. R

    New Holland 269 Baler knotter

    Clean the chute out, take 2 bungee cords and pull the stings going up to the twine discs and pull them back to the end of the chute and then trip the knitters. Have some one slowly rotate the flywheel around and watch what s going on. I fought this with my 269 and I found that the knives where...
  6. R

    New Holland 269 missing knots

    from what I can see if I m not too late is it looks like one end held a knot but the other slipped through. Can see the two strings look like they where in a knot but it looks like it just didn t hold. Do you think billhook tension?
  7. R

    NH 488 Haybine breaking knife drive bolt

    that bearing presses out from the bottom. There is a shoulder that bearing gets pressed into.
  8. R

    New Holland 269 missing knots

    I have a New Holland 269 square baler. It is a beautiful baler and makes wonderful bales. Ever 75 bales or so it will miss one knot then the next and then it will correct itself and be fine for another 75 or so. It is last years twine in the box but I m too cheap to replace as they where brand...
  9. R

    New Holland 461 Haybine Slip clutch repair

    ust out of curiosity what would happen if I attempt to mow with it welded with a tractor without a live pto? My grandfather just dropped off his Farmall M as he stated "it just sits in the shed and might as well be worked". Was kind of wishing now I would have rebuilt it as I kind of want to use...
  10. R

    New Holland 461 Haybine Slip clutch repair

    considering I m coming from a sickle mower to this machine I couldn t be more happy with it. Tickled pink. Mows like it s band new.
  11. R

    New Holland 461 Haybine Slip clutch repair

    I welded it together and it works great until the tensioner sprocket bearing went out anywho that s a sinple fix. Thanks for all the help.
  12. R

    New Holland 461 Haybine Slip clutch repair

    Welding then together was what I was thinking. Is there a timing procedure? Or just grab the welder and go to town?
  13. R

    New Holland 461 Haybine Slip clutch repair

    I have a 461 haybine that the slip clutch pins broke that drive the conditioner rolls. Looking for some guidance on ways to repair this and the best way to remove the clutch. Thanks in advanced
  14. R

    NH 488 Haybine breaking knife drive bolt

    Ok fellas I found the issue. Found a the eccentric collar had come loose in the lower end of the support connecting the wobble box to the knife bar. Rolled it around and found play back and forth there. See photos attached. However I cannot seem to remove that bearing from the housing. Not sure...
  15. R

    NH 488 Haybine breaking knife drive bolt

    I have a New Holland 488 Haybine that is giving me fits. I can mow roughly 30 acres or so and the bolts breaks that connects to wobble box to the knife drive and then the bushing goes out. I have replaced a few of the guards that I thought would be the issue and it still is break. I removed the...
  16. R

    Wrapping the bill hook

    anyone here have a picture of where the springs hook to for the ticker fingers? I have 2 springs but neither where hooked up and I think where I have them is causing a conflict. Thanks in advanced
  17. R

    Sickle mower help!!!

    Figured out how to upload photos This post was edited by Round3Ranch on 06/04/2021 at 07:40 pm.
  18. R

    Sickle mower help!!!

    This post was edited by Round3Ranch on 06/04/2021 at 07:46 pm.
  19. R

    Sickle mower help!!!

    I blew the bushing on the center of the twin arm wobble linkage. I called the local agco dealer and they where kind of lost as to where I was talking about. If the photo loaded see photo for where it is. Is this bushing/bearing still available or how has anyone else rigged this to work. I...
  20. R

    Wrapping the bill hook

    Update on baler thanks everyone for the help after getting twine unwrapped from hook and ran again I found what happened was the tension on the twine coming out of box slipped off on one side and allowed that side to get slack and when the needle came up thats what wrapped. Then found that the...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top