(800) 853-2651
SHOP NOW

Search results

  1. M

    New Parts/Wiring and Starting Problem

    Thank you both!! Having never had the correct electrical components (start button, 3 post solenoid, ignition swith) and with the solenoid mounted to the bottom side of the tool box, I wasn't sure about placement of the new solenoid. I did purchase the heavy copper bar to connect it to the...
  2. M

    New Parts/Wiring and Starting Problem

    I did not try to jumper 12V to the small solenoid terminal. I was considering it and then it started to rain! I don't think that terminal is actually shorted to ground. With the wire connected from the push button, I measured resistance from the small solenoid terminal to ground. It was 3 or 4...
  3. M

    New Parts/Wiring and Starting Problem

    52 8N side Mount 12V This tractor was converted to 12V by a previous owner. It has an automotive type ignition switch, NO push button start switch and 4 terminal solenoid - and a rat's nest under the dash. Today I installed a push button start switch, a 2 wire key switch and a 3 post solenoid...
  4. M

    Electronic Ignition Question

    I haven't been on this forum for a very long time but good to see the voices or reason and authority (JMOR, Hobo, TOH, etc.) are still around sharing their wisdom and experience!!
  5. M

    Electronic Ignition Question

    There were NO instructions! I just went back to the item page on Amazon and it is no longer available :) Looked at a couple other items that were similiar - probably the same - and the reviews on both said no instructions!! :)
  6. M

    Electronic Ignition Question

    I do not currently have suppression plug wires...
  7. M

    Electronic Ignition Question

    And I may just do that! As an Amazon "tester" I was provided a free no-name electronic ignition module. It has been sitting on the shelf for several months. Finally got my tractor running good again (carb rebuilt and new plugs - 2 were fouled). I am in the process of correcting my wiring to...
  8. M

    Electronic Ignition Question

    52 8N Side mount distributor 12V My 12V conversion, done many years ago by a previous owner, apparently retained the 6V coil because there is a ceramic resistor in the 12V line feeding the + terminal of the coil. My question is -- when connecting the +/- wires from the electronic ignition...
  9. M

    8N Solenoid Mounting Screws

    Thank you!!
  10. M

    8N Solenoid Mounting Screws

    Does anyone know the size screws used to mount the solenoid to the starter?? For all the years I've owned my tractor, I've had a rat's nest of wiring with a 4 post solenoid, no start button, etc., etc., and I'm trying to get it closer to "standard" 12V, side distributor wiring. The current...
  11. M

    Question About Carb Rebuild

    Thank you! What happens if you turn it the other way? (Hehehe) Asking for a friend... :) This post was edited by mbramble on 11/30/2023 at 09:05 pm.
  12. M

    Question About Carb Rebuild

    Since I couldn't find anyone to rebuild my carb, I finally ordered a kit. There is a young lady who does tractor repair videos on YouTube. In her rebuild video she shows the choke valve being positioned one way on the choke shaft. In an animated video from the Jus8Ns YouTube channel it is shown...
  13. M

    Who Is The Goto Guy For Carb Rebuilds These Days??

    Thank you!
  14. M

    Who Is The Goto Guy For Carb Rebuilds These Days??

    Well, I guess I'll do it when things settle down in the fall! :)
  15. M

    Who Is The Goto Guy For Carb Rebuilds These Days??

    I just spend enough time trying to keep push mowers and riding mowers working at the time. Right now with heat and rain, some part of my property needs to be mowed every couple days. Would just rather have someone do it and get it right. Used to be a couple guys on here who did them. Maybe...
  16. M

    Who Is The Goto Guy For Carb Rebuilds These Days??

    I haven't been on the Forum for quite awhile! I had corresponded with one guy a few years ago about rebuilding the carb that came on my parts tractor. It had supposedly been rebuilt but I wasn't too confident in the guy's abilities after seeing some of the other things he'd done :) Long story...
  17. M

    PTO Shaft Removal

    Mission creep has set in!! The reason for pulling the shaft is that the hole at the end of the shaft for securing an ORC (or whatever) had been wallowed out over the years and the roll pin would not stay in place. It kept getting "sheared off" at one end allowing the ORC to come off. I had...
  18. M

    PTO Shaft Removal

    Thanks, I really don't want that!! I have only pulled two PTO shafts before and in both cases the fluid was drained because other work was going to be done
  19. M

    PTO Shaft Removal

    Thank you, sir!!
  20. M

    PTO Shaft Removal

    Can I just park with the nose facing downhill to keep from having to drain the fluid???
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top