(800) 853-2651
SHOP NOW

Search results

  1. T

    4020 steering re-build clip

    Yes , most of the valves come in UPS from all over,, I did a valve for some one in Maine a few years ago,, The steer valves weigh 74 pounds I just sent one to Salt Lake city it cost $192 one way,,to Iowa area about $90 or so. Parts and service usually run around $400 exchange plus shipping,, I...
  2. T

    4020 steering re-build clip

    No,, I have never used the stones,, my old dealership never had them when I was there,, I clean them well and if a set looks a bit grungy I swap them out with a good set,, I keep a lot of spare parts for them..
  3. T

    JD 4020 Lost 1/2” wrench in rear housing

    Yes,, Jim has the right idea,,a magnet won't bring it out from under the load shaft,,
  4. T

    JD 4020 Lost 1/2” wrench in rear housing

    It's in under the load shaft...don't ask me how I know that.....
  5. T

    4320

    I work on several 4320's here,, they are a good strong tractor,,one weakness is the dry clutch,,and the PTO operating issues..
  6. T

    4020 steering re-build clip

    Here is a clip a friend of mine posted on You Tube..It shows a little of what is involved with the re-build process..
  7. T

    John Deere 3010 leaky brakes.

    I would be glad to rebuild your brake valves here and bench test [email protected]
  8. T

    JD 3020 gas gauge issue

    It's possible that your gauge is receiving higher voltage from the alternator,,a new gauge may deal with that better, one way of checking this is to remove the hot wire on your alternator and see if it makes a difference..
  9. T

    3020 syncro hydraulics

    On the latter 3020/4020/4320's, the PTO valve is one of the first places suspect of internal leakage,followed by the SCV's,, when you have leakage your stand-by oil supply drops near immediately after you depress the clutch pedal on sychro range tractors,,to sort it out plug off one unit at a...
  10. T

    4440 wedge beater pipe

    I don't use that method,, I remove the 3 outer bolts.maybe leave 2 or 3 threads in,,remove the pinion cog pin,, loosen or remove the 3 inner bolts if you can get to them,,then using a floor jack and the correct length 2x6 on it for a platform set a 20 ton jack between the load shaft pin area on...
  11. T

    3020 syncro hydraulics

    Yes,, I have done that on a couple 2440's to keep the loader working
  12. T

    4x4 ratio

    You won't notice the difference,, most front wheel assist are 5-7% faster on the front, and any front wheel assist tractor will fill the front wheels off quickly if you run them on a hard road when engauged .
  13. T

    wapsi couplers

    I have used several dozen here the past year, yes they are the way to go,,
  14. T

    Need Workshop Ideas! Taking down Storage Shed and Building Bigger!

    I disagree on putting floor drains in,,I have been involved in setting up several shops,, and have worked in many farm shops when I worked off a truck,,flat floors except a slight slope near the entry door (to let snow and ice melt off and get away,in cold areas) When your trying to split or...
  15. T

    Engine stands

    I have a little 5,000 lb fork lift that I can't live with out, When I split a front end off to get an engine out I carry the front half out side out of the way.
  16. T

    Engine stands

    Here is a pic of the lift mounts
  17. T

    Engine stands

    Mine is made from a 4400 final, it has a 7 to 1 ratio,, I made a spring loaded lock ring with 6 holes in it,,I have the stuff to make a heaver lock pin just to make it safer.. I have to pull it off to put the rear main seal in.., I made 4 bolt on lift points with square tubing that bolt on to...
  18. T

    Engine stands

    I have a 466 hanging on mine now,, It's the 10th one this year.. I have a completed 466 that I have on a shipping stand now,, getting ready to fire it up..I just went through it,, it was a walk in ,,in boxes..I was afraid my rotator lock would not handle the engine torquing up..I plan on...
  19. T

    Engine stands

    I thought about a side mount set up but chose the end mount,, all I work on are 404/466 engines and they are more than safe to hang by the end
  20. T

    Need Workshop Ideas! Taking down Storage Shed and Building Bigger!

    I use roll up doors here ( the kind that roll into a drum) and I like them a lot,, when they are open they don't cover up the over head lights
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top