(800) 853-2651
SHOP NOW

Search results

  1. A

    Needing baler parts

    I have those sweep feed fingers and the pads new and a used pin and snap ring.
  2. A

    Help with engine identification

    Do your injectors go into the side of your heads or are they on top next to the valve covers?
  3. A

    Need a little help with brake shoe direction - 1952 Case VAI

    As you can tell, I used a hammer and chisel to remove the drum I sent to you. I think I tried a long 3/4 drive ratchet on there, but was not able to keep the shaft from turning enough to break it loose. From your picture, it looks like your bolt might have more rust than mine did. A method that...
  4. A

    Jack Pad and Base

    Check with Jerry Sanders. Email [email protected]
  5. A
    Expired

    For sale Case 300 transaxle

    can load 330-four16- four six 82
    $250.00
  6. Combine tire
    Expired

    For sale Combine tire

    50% tread, can load 330-four 16-four six 82
    $75.00
  7. A

    oil pressure relief valve

    It's on the oil pump. Have to remove the oil pan. Did someone put a pump from a diesel engine in it? They run about 80 pounds pressure.
  8. Case 300 round nose bolster and dual wheel front pedestal
    Expired

    For sale Case 300 round nose bolster and dual wheel front pedestal

    can load 330 four one 6 four six 82
    $180.00
  9. A

    Case 300 push rod tubes leaking oil.

    Oops, I didn't realize that the early heads, the VAC and early 300, had no o-rings. I thought all those heads with push rod tubes were the same. I guess all the ones I have worked on were either 148B or 159 engines.
  10. A

    Case 300 push rod tubes leaking oil.

    Those tubes have been a trouble spot on any Case small block gas head for years and those early VAC engines are 80 years old. The best time to replace them is when the head is off for a valve job and the tubes are somewhat cleaned. The o-rings are standard dimension, but make sure you get good...
  11. A

    Long Gone

    To this day there are a few smells that take me back to those memories of the local Case dealer. A trip there with my dad was better than any candy store or amusement park. The smells of a little leaked gasoline in the shop, cigarette smoke at the parts counter (which was one of the few places I...
  12. A

    Case IH 595 hydraulic issues when hot

    I had a 674 IH that was acting like that and after rebuilding the orbitrol steering pump I noticed that one of the remote hyd. levers was stuck in the full stroke position and causing the hydraulic oil to heat up.
  13. A

    Hydraulic Power Shuttle Transmission dead?

    I have a service manual for that machine for sale if you need one. [email protected]
  14. A

    Robert Bosch P pump on Ford F-800

    I am trying to remove the injector pump on a 7.8 L Ford engine because the truck was setting for several years and the pump is not putting out fuel. I have a manual for the truck engine and have removed all the lines and controls to the pump. I have taken all the bolts out that hold the adapter...
  15. A

    Case 611B hydraulics

    They are made that way. That rectangular bock that your hoses are threaded into is called an interlock and the engine has to be running to move any hydraulic fluid. Even the Eagle Hitch won't go down without the engine running.
  16. A

    430 DOM lift piston sticks in rockshaft housing

    Thanks for the reply Tgrasher. His cylinder walls ended up being beat up a little. After he got the bumps smoothed out and the cylinder bore honed it's working smoothly.
  17. A

    430 DOM lift piston sticks in rockshaft housing

    My neighbor is working on his 430 Draft-o-matic that he bought recently and every time he lifts the 3pt. hitch up the piston in the rockshaft housing sticks in the raised position so tight that he has to take the rockshaft housing apart and pound the piston out of the cylinder.
  18. A

    vac hydraulic pump

    I have those cages, VT5048 new old stock, for a pump without inserts.
  19. A

    sediment bowl gasket

    I also had a hard time finding those gaskets. I got some either from John Saeli or Case IH. But I have a bunch of the wrong size gaskets that were supposed to fit Case that I ordered on line. As far as I know, Case always used the same sediment bowls up through the 1960's. A11208 was the part...
  20. A

    Oil pressure indicator on Case Model C

    Bob, as I recall ( I don't have a picture in front of me), there is a system of oil pressure lines inside the crankcase and one of those lines feeds that oil pressure indicator on the inside which is just a spring loaded plunger that responds from the oil flow in that system. If you remove the...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top