(800) 853-2651
SHOP NOW

Search results

  1. M

    Ford 730 Loader on Ford 3600

    I ended up replacing the 2.5 inch bolt with a 3 inch bolt. cut the bolt pattern into 1/2 inch steel place and placed rubber washers between the plate. The pump now sits perfectly. I plan on uploading a video to youtube on how to do the crankshaft pulley attachment as well as getting the 730...
  2. M

    Ford 730 Loader on Ford 3600

    Otherwise if I have it half on the crank shaft and half on the pump it runs for a little bit but any jerk causes it to slip off. I did this once and realized it could seriously break something so I have not done anything yet. During those 10 seconds I did test the hydraulics and everything seems...
  3. M

    Ford 730 Loader on Ford 3600

    Finally the snow is gone enough where I can work on the tractor. Finally put in the last pin and she the loader is on. I have run into a problem though. My shaft is about 1-1.5 inches to short. If I put it all the way into the crank shaft pulley it touches the pump but not enough to engage the...
  4. M

    Ford 730 Loader on Ford 3600

    I found where the crank shaft pulley is located and on the 3600 there is a belt guard that I can take off and that grants me easy access to it. Attached is a picture of the 6T spline attached to the crank shaft pulley. its been bugging the hell out of me why this is so weird and decided to look...
  5. M

    Ford 730 Loader on Ford 3600

    The pump is 13 spline. everything that I am finding online is 13 spline as well for the pump. There is a guy down the road who has a yard full of tractors and construction equipment. I stopped by and he talked to me for a couple hours and showed me all his old hydaulic pumps and they are all 13...
  6. M

    Ford 730 Loader on Ford 3600

    If I go onto the 730 page for parts I can find the the 13 spline hydraulic pump drive. though on that page there are no adapters or pump drives that are 13 spline to 6 spline. https://www.yesterdaystractors.com/Ford-730_Hydraulic-Pump-Drive-For-730-Loader_292222.html
  7. M

    Ford 730 Loader on Ford 3600

    I found this on Yesterday Tractors parts listing under PTO but its 23 spline not 13. https://www.yesterdaystractors.com/Ford-3600_PTO-Countershaft_C5NN702A.html
  8. M

    Ford 730 Loader on Ford 3600

    I took some pictures. the front of the tractor has a hole in the front that goes back about 10 inches and there is a female 6 spline. where as the shaft of the hydraulic pump and the bar with splines on it that should go into the hole being 13 spline. The hydraulic pump is also 13 spline. I...
  9. M

    Ford 730 Loader on Ford 3600

    The loader is in immaculate condition. Everything is clean and he showed me videos of it running on his tractor and we spent about an hour and a half going over how to hook the loader up what modifications to my tractor are needed how much work its going to take and answering all my questions...
  10. M

    Ford 730 Loader on Ford 3600

    I messaged the seller and he confirmed he has already taken the pump shaft and coupling off of his tractor and is selling it to me. I made sure the seller knew that I wanted to inspect his tractor and see how he installed and take some notes so I can get it installed. This is my first time doing...
  11. M

    Ford 730 Loader on Ford 3600

    I am purchasing a Ford 730 for my Ford 3600 Tractor. The loader is coming off of a Ford 3000 but from my research this should work. My question for the amazing people on here that always point me in the right direction is how do I hook up the hydraulic pump to the front PTO? the seller sent me a...
  12. M

    Ford 3600 and the fasco1200 loader

    Most northern portion of Michigan. Found a place by Detroit that has a 3600 gas with a 730 on it that I'm waiting on a call back if they will separate. But that's a 9 hour drive one way lol. So if that dealership will separate then it comes with a front crank pump and side lever controls so I...
  13. M

    Ford 3600 and the fasco1200 loader

    Wish I could have picked up the loader. Guess the guy thought 6 hours was to far of a drive for someone to make for it. So instead of letting me pick it up sunday he sold it to another guy. I guess the hunt continues for a loader.
  14. M

    Wont start with Key but can with wrench

    Yes I do. And I feel kinda dumb because I was using it for 6 months with the key just fine and then it just stopped working and I guess I stopped putting it in neutral on the high low when I was done for the day. First tractor with that feature. I'll make sure I read the manual again in case I...
  15. M

    Wont start with Key but can with wrench

    Reporting back. Tractor will start when my hi low shifter is in the neutral position. Will not start in high or in low. Iv had the tractor since January. Is this normal behavior?
  16. M

    Wont start with Key but can with wrench

    For some reason I can't post the pic. But yeah I just jumped the wire and it turned right over.
  17. M

    Wont start with Key but can with wrench

    Bypassed the neutral switch and started right over. Is this an easy replacement?
  18. M

    Wont start with Key but can with wrench

    I know there is nothing wrong with the battery as its brand new from earlier this year and it starts every time I jump the tractor with the wrench.
  19. M

    Wont start with Key but can with wrench

    I have a Ford 3600 diesel where the key start just stopped working a couple months ago. I know I can just jump the starter with a wrench to start and that has been working for the tiny amount I was using the tractor. Well now I am using the tractor every day and I dont want to do permanent...
  20. M

    Ford 3600 and the fasco1200 loader

    This is coming off of a 3000 series and I have a 3600. The measurements and reading the manual makes me think it will actually fit. As for the remote controller I am not a fan of it being under the seat as it makes it awkward to access. I can reach it bending down but my wife cant reach it very...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top