(800) 853-2651
SHOP NOW

Search results

  1. S

    Allis Chalmers WD45 Steel discharge ling on power steering

    Tom thanks again. I found one in Clinton, Missouri as they had. I couldn't be happier especially from the help I got here on the forum. Again thanks Joe.
  2. S

    Allis Chalmers WD45 Steel discharge ling on power steering

    4wdtom thank you very very much sir!
  3. S

    Allis Chalmers WD45 Steel discharge ling on power steering

    4wdtom thank you very very much sir!
  4. S

    Allis Chalmers WD45 Steel discharge ling on power steering

    I have a 1956 Allis Chalmers WD45 with power steering. It's the belt driven type pump on the top leff front of the engine. The pressure discharge line on it is attached the pump, at the bottom, with a little square block (I believe brass) with a large hole in that a Banjo Bolt passes through to...
  5. S

    Allis Chalmers WD45 Hydraulic Oil Pump

    Okay what I've found so far is on the valve assembly, the one controlled by the adjusting screw, the two O rings on the one valve were hard and brittle, and that wavy washer near the end toward the adjusting screw was missing. Working on rectifying that now.
  6. S

    Allis Chalmers WD45 Hydraulic Oil Pump

    DrAllis....So far all I've done is removed those balls to see if they were stuck. They were fine and undamaged. I put them back. All the pump pistons are fine and go up and down smoothly. I did remove the adjuster screw sleeve and all it's parts and they looked fine too. I removed the cam...
  7. S

    Allis Chalmers WD45 Hydraulic Oil Pump

    Guys I posted a question on this year or more ago that the pump isn't pumping. I got a reply about pulling the pump and something about each little individual piston being stuck or something. Well finally got it off and part and nothing is stuck or rust or missing parts. The ball seals look...
  8. S

    ALLIS CHALMERS WD45 HYDRUALICS

    All the linkage is hooked up. I even worked it by hand and nothing. I didn't think it was going to be a simple easy fix.
  9. S

    ALLIS CHALMERS WD45 HYDRUALICS

    I have an Allis Chalmers WD45. The hydraulic pump was working fine and then one day went to raise the bush hog and nothing! I checked the oil and it's full. Screwing the adjusting screw in and out makes no difference now. Before all the way in and there was no pumping pressure. Screwing it out...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top