(800) 853-2651
SHOP NOW

Search results

  1. T

    Massey Ferguson 255 Aux Hydraulics

    Possible that the spring loaded detents have been bottomed out due to broken springs or rusted in place.
  2. T

    Massey 175 transmission top cover

    I'll offer this. I have a 150 with IPTO and to clean the hydraulic pump strainer the top cover had to come off. I didn't have any problems. I don't know if your 175 is much different 🤷
  3. T

    MF 50 leak

    On my 150, I drilled a hole in this plate and installed a cotter pin like forward drain hole.
  4. T

    Y T tractor show

    My 1967 MF 150 before n after seven months rebuild.
  5. T

    Thank You Big Dean

  6. T

    Thank You Big Dean

    I have Big Deans MF repair disk loaded on my laptop. He had a wealth of information on those disks. Too bad his family didn't continue to make them available after his passing.
  7. T

    New MF135 Owner!

    What John said ! My 150 $5000 later.
  8. T

    Pondering new cell phone service

    I also am considering a change from Verizon. I'm concerned with coverage. No problem at home in Ohio but winters in the woods of SC is a problem. I'm only 2 miles from tower but on certain days signal is very weak. The 70 foot Lob Lolly pines surrounding my cabin are a problem. Is there a way to...
  9. T

    Source for adjustable 3pt stabilizer bar

    Got mine from TSC for 150MF
  10. T

    Just Curios

    I have the early Ryobi inflator. Works great on wheel barrow and motorcycle tires. It will top off my Silverado tires but takes several minutes. If tire was below 20 psi I'd use a clamp to hold the trigger.
  11. T

    External hydraulic remote on Massey 65

    Directional valve has "Power Beyond" capabilities. Can stack more together with one pressure and one tank port.
  12. T

    construction screws with torx drive

    Last I bought were from local hardware, they sold in bulk @ $3 a pound cheaper than Lowes. Now their Vendor only supplies them boxed 😞
  13. T

    Battery cable query

    Where I worked, we had Baker drills that used up to 3" diameter #5 tapered shank bits. These machines were 10-12ft high and spun the 14-16 inch long bits at 200 RPM max in forged steel. A few men actually had their shirts ripped off, being caught in the long chips. Luckily the emergency stop...
  14. T

    Battery post terminal cleaner

    I drill and tap a 3/8-16 thread into posts on my boat batteries and 1/4-20 for lawn tractor batteries. Saw off a SS hex bolt, double nut it so it can be screwed to bottom of thread, remove nuts, ready to go. Hint "Don't over-tighten"
  15. T

    Tach Cable MF 150 Gas

    Thanks Jim, The assembly # I've found is 506331 M91. It's ordered
  16. T

    Tach Cable MF 150 Gas

    I need to replace the inner Tach cable on my 1967 MF 150 Gas engine. I have the original parts book: Inner Cable 1 751 694 M1 (38 29/32") Outer housing 506 331 M91 I don't see a part number for the complete assembly Current part numbers would be appreciated. Thanks Picture is after 2007...
  17. T

    Massey 135 diverter valve.

    I don't see the new one either. Is the old one supplying pressure to two applications at the same time? New one may have Port A and Port B to supply oil individually.
  18. T

    What tractors had the Chrysler six

    Not a helpful answer, but Chris Crafts in the '40s and 50s used Chrysler flatheads, along with several other industrial engines. Our 1948 had a 300 cubic inch Hercules 6 cylinder flathead. Fastest boat on Buckeye Lake even into the early 60's.
  19. T

    Where to connect Massey Ferguson 203 stabilizer bars/chain?

    Radius of a Circle MUST match !
  20. T

    MF302 - Sticking Spool Valves

    Sounds like varnish on the spools. Put a couple quarts of good ATF in hydraulic oil tank. ATF has high detergent content.
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top