(800) 853-2651
SHOP NOW

Search results

  1. H

    140 Hydraulics quit working after sitting for 15 mins

    Thanks Jim. I appreciate the follow-up. I will make sure he has the tractor running. LOL. What would you say is the most likely culprit for an air leak? I know that they used this same system on various models.
  2. H

    140 Hydraulics quit working after sitting for 15 mins

    I have a friend that has a 140. The hydraulics seem to function but then when the tractor is shut off the hydraulics no longer work. He says if he takes the pump off and starts mucking with it and put it back on it will start working again. I told I thought it sounded like a vapor lock. At this...
  3. H

    IH 240 utility part identification

    You are correct. Found it. Thank You.
  4. H

    IH 240 utility part identification

    It has vertical exhaust. At least it does now.
  5. H

    IH 240 utility part identification

    I am putting a IH 240 back together that i have had apart for awhile and need to know where this part goes. See picture. Also my battery box is basically gone. It sounds like the original battery box tops are not available but what about the lower battery box frame? Or do i need to just make one?
  6. H

    Valve Adjustment Clarification on International 240 - C123

    Interesting. Just curious if the wear was due to lack of oil? How does rhat side of rge rocker and the end of the valve get oiled? I noticed when mine was running tonight thar that side does not get the oil like rhe pushrod side does.
  7. H

    Valve Adjustment Clarification on International 240 - C123

    Thanks for everyone’s responses. We obviously all think alike. It kind of surprised me when I saw the setting on exhaust off factory spec. And it was in reference to the manual saying .014 hot for both. I know there were some changes to the 240 engine mid production so I was not sure.
  8. H

    Valve Adjustment Clarification on International 240 - C123

    Thanks Jim. That is what I was leaning towards as the manual could not be too far off. Thank You for providing you knowledge as always.
  9. H

    Valve Adjustment Clarification on International 240 - C123

    I just had the head rebuilt for my 240 with C123 engine. It looks like the intake and exhaust valve clearances are listed as .014 hot. So far I have adjusted the valves at .016 cold and the engine starts and runs fine. This is a heavily discussed topic here and other forums and there are many...
  10. H

    Simple 240 generator wiring routing question

    Well Thank you! That is an impressive answer. Based on your answer i now know how the other cable holders go also.
  11. H

    Simple 240 generator wiring routing question

    Hello everyone. Happy long weekend. I am hoping to get a quick answer on this. I am putting the head back on my 240 that has been in the shop for awhile. The generator wire routes under the mounted triangular thermostat housing that has three bolts. Two of the 3 housing bolts had a wire harness...
  12. H

    Farmall 544 Gas C-200 Valve Clearance?

    Thank You Jim for confirming.
  13. H

    Farmall 544 Gas C-200 Valve Clearance?

    Thanks for the reply. I read the .027 specs also on thread or two but it seemed a little wide compared to the smaller IH 4 cylinder engines such as the C123. It would be nice to confirm it via the service manual which I don't have.
  14. H

    Farmall 544 Gas C-200 Valve Clearance?

  15. H

    Farmall 544 Gas C-200 Valve Clearance?

    Can anyone confirm what the valve clearances are on a Farmall 544 C-200 Gas tractor please.
  16. H

    Wiring Problems

    If the switch itself is arcing I would say it is bad. If it is arcing at the cable connection then clean and tighten it. If it is a new switch I would not be surprised that it is bad as the new ones are very cheaply made. All the switch does is take voltage in and when the switch is engaged it...
  17. H

    Gasket sealer

    I have been using Right Stuff gasket sealer. Seems to setup a lot quicker. Not cheap but works great.
  18. H

    574 water in oil?

    Kind of what I was thinking also. Well the tractor has brand new rear Titan Tires and a nice 2250 loader. Maybe I can get it for scrap value and part it out and find another tractor to put the loader on. Tires may be worth what I get the tractor for. I would like an older Farmall square nose...
  19. H

    574 water in oil?

    Diesel
  20. H

    574 water in oil?

    I know this is a common question and there could be multiple reasons but my question is a little different. Looking at this tractor that came for sale and it has some issues for sure but when you put water in the radiator it comes out the dipstick tube. Is this for sure a cracked sleeve or...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top