Search results

  1. C

    What seal material for VAC high pressure pump

    What should I use for VAC high pressure pump vt-4850 packing material?
  2. C

    VAC governor worn

    The flyball governor has wear marks on the cone and plate, and the balls have flat spots. It actualy works OK , it does overshoot RPM as a load is applied or the speed control lever increased, but at an acceptable level. But it seams that at some point in time the balls were stuck to the...
  3. C

    Want to run belted equipment only have PTO

    My Ford 641 has no belt pulley is there some way to run belted equipment ? Haven't found a belt pulley Wally
  4. C

    What is this? Sabotoge?

    I don't know if it was ever opened before . The cylinders are 3.25 with little ridge at the top. For the last 30 years it was used on about 2 acres as the owner moved from the farm but could never stop farming. I've used it to mow about 10 acres a few times with a sicle mower and in parades
  5. C

    What is this? Sabotoge?

    I don't undestand it! You might not believe it but I found this blocking the oil hole feeding the rear camshaft bushing on a Case VAC. I don't see anyway it could have gotten in there without the head being off. What is it? Were there Case labor troubles in '47? A disgruntled dealer...
  6. C

    What is this? Sabotoge?

    I had never heard of caltrop until now. These seam small to do much harm but you can buy one on ebay for $65 to $300+ Civil War Caltrops Caltrops / cast iron / c. 1860s Continue Shopping $385 In stock Civil War Caltrops
  7. C

    What is this? Sabotoge?

    Or the repairman? Or the casting process?
  8. C

    VAC Can lift

    I found a "new" cam out of a 156 ci case 210 looks good. Other than the cam this engine looks in great shape and quite clean. So what whould plug up the oil hole to the rear bearing? This was over the hole covered in sludge.
  9. C

    VAC Can lift

    Some of my rocker arm adjusting screws are turned so far that the lock nut was placed under the rocker. Trying to find what is worn or bent What should the lift be on VAC valves, measured on top of the valve retainer ? Thanks Wally
  10. C

    VAC Can lift

    The block is OK, bearings are shot. Oil passage was plugged. (Ignor the orange that fell in as I was working )
  11. C

    VAC Can lift

    I need a new cam can't find new on interent. I have access to a used one from a 148 ci engine will that work? What's the difference? What other cams will work? Thanks Wally
  12. C

    VAC Can lift

    NO
  13. C

    VAC Can lift

    Can the camshaft be removed through the governor inspection plate? This plate is not mentioned in my service manual but it looks like it might fit. wally
  14. C

    VAC Can lift

    I can't find a source for a new cam. Any ideas?
  15. C

    VAC Can lift

    I will be looking at the crankshat and rod bearings next. then I'll pull the head I'm trying to decide to rebuild completly or not
  16. C

    VAC Can lift

    I measured the spring height and valve travel as follows valve # 1) Exhaust 1.89 height .235 travel 2) Intake 1.89 .218 3) Intake 1.90 .222 4) Exhaust 1.92 .240 5) Exhaust 1.87 .263 6 )Intake 1.87 .190...
  17. C

    VAC Can lift

    That makes sense And I'll have to measure each push rod and other parts if I really want to find what's different even if I can't find the specification thanks wally
  18. C

    VAC Can lift

    I haven't pulled the pushrods but they all spinned freely. I was checking the valve lash was I saw the different locknut positions. This tractor started running poorly and am thinking of going throught the engine and I couldn't find a specification for cam lift. I thought I would put a dial...
  19. C

    VAC TIMING GEAR

    When installing a distributer does it matter if your are off by a tooth or two on the gear as long as you can rotate the distributer to compensate?
  20. C

    VAC TIMING GEAR

    So what seems to be my problem. Points are set to open, Flywheel is at TDC thanks W

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top