Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

IH 444 loader front pump shaft?


 
Post new topic    
View previous topic :: View next topic  
Author Message
hbo444
New User


Joined: 25 Nov 2020
Posts: 4


Report to Moderator

PostPosted: Tue Jun 22, 2021 6:32 pm    Post subject: IH 444 loader front pump shaft? Reply to specific post Reply with quote

The front hydraulic pump shaft and engine coupler spline are shot on my IH444. Does anybody know where I can get those two pieces?

This post was edited by hbo444 on 06/23/2021 at 08:02 am.

 
Back to top
View user's profile
caterpillar guy
Tractor Guru


Joined: 24 Jun 2007
Posts: 7957


Report to Moderator

PostPosted: Wed Jun 23, 2021 3:49 am    Post subject: Re: IH 444 loader front pump shaft? Reply to specific post Reply with quote

IF the shaft in the pump you will probably have to get a new shaft or pump. For the other parts if they match a pto spline you coulds get pieces of those parts for new shaft and spline. The shaft can be made fairly easily. Pump shaft is where you're going to have to look some.
 
Back to top
View user's profile
hbo444
New User


Joined: 25 Nov 2020
Posts: 4


Report to Moderator

PostPosted: Wed Jun 23, 2021 6:48 am    Post subject: Re: IH 444 loader front pump shaft? Reply to specific post Reply with quote


It's the engine side coupler and shaft spline that are bad. Thankfully - pumps are expensive!
 
Back to top
View user's profile
wore out
Tractor Expert


Joined: 01 Oct 2019
Posts: 2928


Report to Moderator

PostPosted: Wed Jun 23, 2021 10:31 am    Post subject: Re: IH 444 loader front pump shaft? Reply to specific post Reply with quote

Check out the link below, is that the type of drive you have?

Part numbers are shown, look to be obsolete from FIAT, you could try GOOGLING them to see if there's any NOS pieces or good used available.

This very site, in the Ford section, has shafts and couplers available for certain Ford models, perhaps something there could be adapted.

Also, check out the Surpluscenter.com site, they have some splined shafts in that size range and (possibly) some couplings or splined hubs to match.
2444 stinger pump drive

 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters