Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

1940 John Deere B Brake shaft dusk cover removal


 
Post new topic    
View previous topic :: View next topic  
Author Message
Til Valhalla
New User


Joined: 22 Jan 2021
Posts: 5


Report to Moderator

PostPosted: Thu Jun 24, 2021 5:12 pm    Post subject: 1940 John Deere B Brake shaft dusk cover removal Reply to specific post Reply with quote

Hello everyone,
I have a 1940 john deere b that I had
recently taken the brakes off of for a
little inspection. Well the shaft on the
right side's threads have been warped
somehow so now I can't get the castle nut
back on. I am just wondering how you get
the inner dust cover off so that the
shaft will come off. From what I can see
there are rivets on both sides but I am
completely lost right now. Any help is
appreciated.

Til Valhalla
 
Back to top
View user's profile
wore out
Tractor Expert


Joined: 01 Oct 2019
Posts: 2770


Report to Moderator

PostPosted: Thu Jun 24, 2021 5:34 pm    Post subject: Re: 1940 John Deere B Brake shaft dusk cover removal Reply to specific post Reply with quote

CVPost-Til Valhalla wrote:
(quoted from post at 18:12:10 06/24/21) Hello everyone,
I have a 1940 john deere b that I had
recently taken the brakes off of for a
little inspection. Well the shaft on the
right side's threads have been warped
somehow so now I can't get the castle nut
back on. I am just wondering how you get
the inner dust cover off so that the
shaft will come off. From what I can see
there are rivets on both sides but I am
completely lost right now. Any help is
appreciated.

Til Valhalla






You said it was a 1940, so the first diagram should apply.

If you've already had the drum and shaft out to service the brakes I'm not understand what "shield" you would now now need to remove to again remove the shaft?

Can you provide a bit more detail of what the issue is?
 
Back to top
View user's profile
Til Valhalla
New User


Joined: 22 Jan 2021
Posts: 5


Report to Moderator

PostPosted: Thu Jun 24, 2021 6:09 pm    Post subject: Re: 1940 John Deere B Brake shaft dusk cover removal Reply to specific post Reply with quote

In the image that i found online it had shown a dust cover then the disk on the end of the shaft, from what I gathered the dust cover had pinned the shaft to the drum. This also could be me overthinking things as I normaly do and the answer is sitting right in front of me.

I can try and show the image that i found, if it shows the circled part is what I am calling the inner dust cover.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Restoration and Repair Tips All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters