Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

TC/MM oil filters.


 
Post new topic    
View previous topic :: View next topic  
Author Message
Duey C
Regular


Joined: 30 Jan 2019
Posts: 31


Report to Moderator

PostPosted: Wed Jul 21, 2021 9:50 pm    Post subject: TC/MM oil filters. Reply to specific post Reply with quote

Some oil filter options have dried up for TC/MM engines.
Just a short snippet of what I know so far.
Fleetguard LF-584's need some help to correctly fit on the 11/16 oil filter stem.
I also found the Henry Leasing FE5905 filter is quite close but may need some "adjustments" to fit some filter housings correctly depending on which nut holds the filter housing down.
The TC/MM 11/16" stem is what gets us in trouble.
Perhaps you have a 1/2" stem on your MM.
Hah! I'd like to know that! And yet I'd like to know.

NOT to promote my own madness/thread but for a small amount of info on oil filters for my 21-32 see posts 915, 916, 919, 920 & 924 starting on page 46 here.: https://www.smokstak.com/forum/threads/twin-city-small-tractors-on-a-whim.180290/page-46
I try to share info as I learn more.

This post was edited by Duey C on 07/21/2021 at 11:31 pm.

 
Back to top
View user's profile
Duey C
Regular


Joined: 30 Jan 2019
Posts: 31


Report to Moderator

PostPosted: Sat Jul 24, 2021 12:03 am    Post subject: Re: TC/MM oil filters. Reply to specific post Reply with quote

Crap, there wasnt much real info shared in that last post was there? A bit more is elsewhere here.
Lets look at the Henry KE-5905 ($35 bucks for me) and Fleet Guard LF-584 ($13 bucks) for a moment.
New filters. Very available.
1. Not bad. The tall nut. Perhaps a lock washer under the nut on the bottom of the stem would raise the filter a bit to suit this tall nut better.
Shown at the depth AS IF the housing were installed.
2. Felt-stack type nut. Wait. It seems a certain 1950 UTS has a similar short nut. Oh oh!
Please dont toss your filter element in and hope itll do its job.
This is a waste of an oil filter in my opinion with the gap. Pay attention.
You MM guys should also know what a felt-stack filter looks like.??? Maybe not.
I have one. Still in a 1930 KT filter housing. Cool.
Remember, the KT and MT were the older brothers to the MM U.
3. Big filters. Quite close to the size of original filter elements.
Was/is there enough room to pass oil around the outside of the filter? Small space.
4. Little fart. The IH Fleet Guard LF-584. We can see the top neck Im holding upside-down in the pic has been size-modified to fit the TC/MM 11/16 oil filter stems.
The bottom neck is fine on both filters.
5. Another option. The Henry KE5905 may want you to downsize the hole in the top neck if you have the short nut. Tin snips and a clamp.
The LF-584 IH filter top neck needs to be enlarged to fit the 11/16 stem then a piece of 3/4 heater hose and a clamp to seal and hold it in place.
A socket and a hammer to drive the top neck down and around the TC/MM stem.
I had to clean up the threads on the stem I used for testing.










This post was edited by Duey C on 07/24/2021 at 01:05 am.

 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Minneapolis Moline All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters