Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Replacement carb for clinton c700


 
Post new topic    
View previous topic :: View next topic  
Author Message
razerface
New User


Joined: 22 Sep 2006
Posts: 6


Report to Moderator

PostPosted: Sun Sep 12, 2021 12:30 pm    Post subject: Replacement carb for clinton c700 Reply to specific post Reply with quote

What carb can i put on clinton c700 to replace busted LMG 8?
Anyone recognize this cast iron wheel system?





This post was edited by razerface on 09/12/2021 at 02:54 pm.

 
Back to top
View user's profile
Gene Davis (Ga.)
Tractor Expert


Joined: 25 Oct 2003
Posts: 2185


Report to Moderator

PostPosted: Sun Sep 12, 2021 12:48 pm    Post subject: Re: Replacement carb for clinton c700 Reply to specific post Reply with quote

Good luck, I have been trying to find one for my Clinton to replace the LMG with the main jet threads stripped out. I tried JB weld on them but it did not hold. Some Tecumseh carburetors will fit just have to change the throttle shaft and possibly the choke shaft
 
Back to top
View user's profile
razerface
New User


Joined: 22 Sep 2006
Posts: 6


Report to Moderator

PostPosted: Mon Sep 13, 2021 6:43 am    Post subject: Re: Replacement carb for clinton c700 Reply to specific post Reply with quote

CVPost-Gene Davis (Ga.) wrote:
(quoted from post at 13:48:54 09/12/21) Good luck, I have been trying to find one for my Clinton to replace the LMG with the main jet threads stripped out. I tried JB weld on them but it did not hold. Some Tecumseh carburetors will fit just have to change the throttle shaft and possibly the choke shaft


I just spoke with Jim's Antique Small Engine Parts in Idaho. He fixes the stripped out threads with a helicoil. $50-60 depending on condition of carb. Carb will come back cleaned and repaired.
 
Back to top
View user's profile
Gene Davis (Ga.)
Tractor Expert


Joined: 25 Oct 2003
Posts: 2185


Report to Moderator

PostPosted: Mon Sep 13, 2021 4:37 pm    Post subject: Re: Replacement carb for clinton c700 Reply to specific post Reply with quote

Thanks for the info. For that price I will have to think on it for a while now.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Lesser Known Classics All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters