Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Worn 656 Shifter


 
Post new topic    
View previous topic :: View next topic  
Author Message
Tinks 1996
Regular


Joined: 12 Jan 2020
Posts: 25


Report to Moderator

PostPosted: Tue Sep 14, 2021 4:39 pm    Post subject: Worn 656 Shifter Reply to specific post Reply with quote

I have a 656 loader tractor that the shifter is getting worn . If you don't shift it slow it will hang in 2 gears . What do I need to look for ? Is there something I can build up ? Thanks for the info .
 
Back to top
View user's profile
used red MN
Tractor Expert


Joined: 24 Aug 2013
Posts: 3299
Location: Coon Rapids, MN

Report to Moderator

PostPosted: Wed Sep 15, 2021 9:42 am    Post subject: Re: Worn 656 Shifter Reply to specific post Reply with quote

Right now the CNHI parts page is down for updates. Need
to know if you have a Farmall row crop or utility model. Do
not know how familiar you are with it but a linkage with two
rods and a bell crank transfer the shifter motion from the
shifter down to the transmission. One for each set of gears
on either side of neutral, as in reverse and first. So there is
3 sets. Tightening up the slack in all those joints is what
needs done, new pins for all the joints is a start. I will link
another parts site that shows the diagram for the Farmall
version. Do a web search on this problem a lot of info will
come up.
Parts diagram

 
Back to top
View user's profile
Tinks 1996
Regular


Joined: 12 Jan 2020
Posts: 25


Report to Moderator

PostPosted: Wed Sep 15, 2021 6:08 pm    Post subject: Re: Worn 656 Shifter Reply to specific post Reply with quote

It is a row crop.
 
Back to top
View user's profile
the tractor vet
Tractor Guru


Joined: 24 May 2000
Posts: 16224


Report to Moderator

PostPosted: Wed Sep 15, 2021 6:19 pm    Post subject: Re: Worn 656 Shifter Reply to specific post Reply with quote

Ah no thqat is not how the shifter works on a 656-686 Ya have THREE RODS running from three levers on a shaft that slide thru the levers with a pin that makes contact with the slot on each lever / arm what ever ya want to call it . What happen is they ware the pin can snap off on one side but not the other and they still will shift but they have more slop now . The ware is mainly between the levers/ arms . I have had some luck with shimming them closer together on the outside of the Rev /1 shifter and the 4/5 shifter and replacing the pin in the slide shaft . You may find ware where the rods connect to the shifter lever arms at the slide rail and also down under the battery box . They are noway near the shifter used on the 06-86 tractors .
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters