Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Sherman


 
Post new topic    
View previous topic :: View next topic  
Author Message
Dylan Berhorst
Regular


Joined: 23 Jul 2013
Posts: 278


Report to Moderator

PostPosted: Wed Oct 13, 2021 5:29 pm    Post subject: Sherman Reply to specific post Reply with quote

what tractors will a Sherman out of a 2n fit?
 
Back to top
View user's profile
Dean
Tractor Guru


Joined: 29 Jan 1998
Posts: 23156


Report to Moderator

PostPosted: Wed Oct 13, 2021 7:01 pm    Post subject: Re: Sherman Reply to specific post Reply with quote

All N models.

Dean
 
Back to top
View user's profile
Den N Ms
Tractor Guru


Joined: 20 Feb 2007
Posts: 6563


Report to Moderator

PostPosted: Wed Oct 13, 2021 8:29 pm    Post subject: Re: Sherman Reply to specific post Reply with quote

Dylan Berhorst, As Dean said all N models, except the early 9Ns with the straight cut transmission gears.It will also fit the 53 Jubilee 54 Naa,Nan and the hundereds series. The clutch disk may have to be changed because of different splines in the hub.Maybe even in the 2000,3000,4000 with a clutch change .but not quite sure on them.Maybe someone knows for sure?
 
Back to top
View user's profile
Kirk-NJ
Tractor Guru


Joined: 10 Dec 2006
Posts: 5940


Report to Moderator

PostPosted: Thu Oct 14, 2021 2:44 am    Post subject: Re: Sherman Reply to specific post Reply with quote

Depends which sherman. The combo will fit all 4 speeds up to the X01 series with serial numbers before 14257. The sherman step up or step down will fit nicely up to the 8n after that some adapting would have to be made to the handle because of the position of the bump out on the bellhousing. It's not impossible but not worth it to add a step up IMO. After the 14256 number you could change out the input shaft and nose cone on the sherman combo to make it work on later series tractors. As far as changing out the clutch disc to earlier course spline you would also have to change out the flywheel. The X01 used a wider flywheel this is why the left brake rod was relocated to under the rear center housing because of no room in the bellhousing. Also the earlier engine plate would have to used to make up for the differences in the trans case and input shaft length. Unless you have all parts on hand I would stay away from tiring to switch out the clutch disc. Any one would sez just change the clutch disc has never done one before
 
Back to top
View user's profile
Kirk-NJ
Tractor Guru


Joined: 10 Dec 2006
Posts: 5940


Report to Moderator

PostPosted: Thu Oct 14, 2021 2:50 am    Post subject: Re: Sherman Reply to specific post Reply with quote

I should add It will not fit the 9n with straight cut gears unless the mating gear in the main trans has been changed out to helical gear which will require a double split. Probably the hardest this on that whole job was getting those dam detent balls back in.
 
Back to top
View user's profile
DMartin9N-2N
Long Time User


Joined: 23 Jul 2007
Posts: 848


Report to Moderator

PostPosted: Thu Oct 14, 2021 1:50 pm    Post subject: Re: Sherman Reply to specific post Reply with quote

Good afternoon, Dylan: Interesting thread; Just as comment, I have a 9N with a Sherman overdrive, not underdrive. It works ok, but for my purpose (finish mower) I have no use for an overdrive. I have tried the tractor on our blacktop road, in 3rd gear (a 9N only has 3 gears), if I put the Sherman in high, and try a full throttle run, it scares me. The tractor is not suited for that high of speed. So mine is just a novelty, something to talk about at a tractor show.

Dennis M. in W. Tenn.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Ford 9N, 2N, 8N All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters