Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

cat 941 track adjustor help


 
Post new topic    
View previous topic :: View next topic  
Author Message
373
New User


Joined: 11 May 2022
Posts: 2


Report to Moderator

PostPosted: Thu May 12, 2022 4:25 am    Post subject: cat 941 track adjustor help Reply to specific post Reply with quote



Help..piston is stuck in the cylinder . I tried pulling on the front idler with a chain to free it up . That didnt work . I have since compressed the spring and unbolted the assembly from the loader. Any suggestions ? Can I use some heat ? I cant remove the rod from the cylinder because the bolts are close to the cylinder head. I could back them out and cut off the bolt heads if I had to .
 
Back to top
View user's profile
dpendzic
Tractor Expert


Joined: 05 Mar 2009
Posts: 2877
Location: long island NY and Hancock Ma

Report to Moderator

PostPosted: Thu May 12, 2022 1:21 pm    Post subject: Re: cat 941 track adjustor help Reply to specific post Reply with quote

I freed mine by soaking with kroil oil and then pulling it back IN first--i think it got cocked crooked and jammed in---then pulled it out and resealed it
 
Back to top
View user's profile
373
New User


Joined: 11 May 2022
Posts: 2


Report to Moderator

PostPosted: Fri May 13, 2022 7:17 am    Post subject: Re: cat 941 track adjustor help Reply to specific post Reply with quote

Did you submerge the whole thing in oil or just spray it on the head part ? How did you get it to pull out ? I think mine is jammed all the way in .
 
Back to top
View user's profile
dpendzic
Tractor Expert


Joined: 05 Mar 2009
Posts: 2877
Location: long island NY and Hancock Ma

Report to Moderator

PostPosted: Fri May 13, 2022 7:32 pm    Post subject: Re: cat 941 track adjustor help Reply to specific post Reply with quote

I just sprayed it with kroil and it must have self aligned when i retracted it--then pumped grease in it to push the cyl out
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Crawlers, Dozers, Loaders and Backhoes All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters