Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

international 300 utility


 
Post new topic    
View previous topic :: View next topic  
Author Message
pinball
Tractor Expert


Joined: 13 Jun 2007
Posts: 2105


Report to Moderator

PostPosted: Fri May 13, 2022 5:02 pm    Post subject: international 300 utility Reply to specific post Reply with quote

i broke my throttle lever. been looking for one for a while. saw one on eBay for 59 bucks listed for the int 300 but its different than mine, don't know if that one listed is for a Farmall 300 or not. mine has a 7/16 hole drilled through it with 7/32 dowel pins. the one they show doesn't have the hole like mine so did the utility have different levers or not. thanks
 
Back to top
View user's profile
used red MN
Tractor Guru


Joined: 24 Aug 2013
Posts: 4296
Location: Coon Rapids, MN

Report to Moderator

PostPosted: Fri May 13, 2022 7:56 pm    Post subject: Re: international 300 utility Reply to specific post Reply with quote

In the link is a 300 utility throttle handle. The IH part number will be 364433R1. The Farmall row crop throttle will have an additional stop tab near the bolt and washer that set in the notches. The tab is about 1/2 in. by 5/8 in. by 3/16 in. thick. Also the on Farmall throttle the hole for the rod it slides on goes through. On the utility the throttle hole is blind and that end of the lever is shaped differently.
Example throttle

 
Back to top
View user's profile
pinball
Tractor Expert


Joined: 13 Jun 2007
Posts: 2105


Report to Moderator

PostPosted: Sat May 14, 2022 5:05 am    Post subject: Re: international 300 utility Reply to specific post Reply with quote

thanks
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters