Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

2870 Case Tractor


 
Post new topic    
View previous topic :: View next topic  
Author Message
Roger Gwin
New User


Joined: 19 May 2008
Posts: 6


Report to Moderator

PostPosted: Mon May 19, 2008 3:32 pm    Post subject: 2870 Case Tractor Reply to specific post Reply with quote

I just bought a 2870 Case tractor. Clutch 2 in the powershift has a bad leak and needs repaired. What is the best way to get to the unit ? Pull the engine or can it be done from the back ? I hope someone can advise me because there are very few in the area. Thanks
 
Back to top
View user's profile
NHBoyd
Guest






Report to Moderator

PostPosted: Mon May 19, 2008 4:03 pm    Post subject: Re: 2870 Case Tractor Reply to specific post Reply with quote

You will have to pull the engine. It would be best to come up with a service manual.
 
Back to top
Roger Gwin
New User


Joined: 19 May 2008
Posts: 6


Report to Moderator

PostPosted: Mon May 19, 2008 4:21 pm    Post subject: Re: 2870 Case Tractor Reply to specific post Reply with quote

Thank you for responding. I will try to locate a service manual. Any suggestions?
 
Back to top
View user's profile
c.hess
Regular


Joined: 08 May 2008
Posts: 121


Report to Moderator

PostPosted: Mon May 19, 2008 5:47 pm    Post subject: Re: 2870 Case Tractor Reply to specific post Reply with quote

There are others better informed but just looking at diagram on case web site it looks similar to 4690 an on that one you need a stand that mounts under engine(large 4 point) an than you can disconect all lines an remove bolts on frame- disconect at bell housing an roll forward. Dont even have to remove radiator or hood on 4690.That is brief description you will do.Case dealers had special stand avaible.
 
Back to top
View user's profile
Roger Gwin
New User


Joined: 19 May 2008
Posts: 6


Report to Moderator

PostPosted: Tue May 20, 2008 5:51 am    Post subject: Re: 2870 Case Tractor Reply to specific post Reply with quote

I wondered about leaving everything together as I was looking thingss over. Good idea.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Talk All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters