Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Post driver on a 685


 
Post new topic    
View previous topic :: View next topic  
Author Message
tom-ky
Regular


Joined: 07 Jun 2003
Posts: 175


Report to Moderator

PostPosted: Tue May 05, 2009 5:43 pm    Post subject: Post driver on a 685 Reply to specific post Reply with quote

Neighbor has a 685 and trying to plumb a post driver on it. Where should he plumb it in at?
 
Back to top
View user's profile
C. Amick
Tractor Expert


Joined: 05 Mar 2009
Posts: 2401
Location: Wytheville, VA

Report to Moderator

PostPosted: Wed May 06, 2009 4:11 pm    Post subject: Re: Post driver on a 685 Reply to specific post Reply with quote

I know that this is not the answer to your question, but the best place to mount one is on the front of a tractor. It make it a lot easier to line yourself up to a post with the front wheel and you are not twisting to look back.
 
Back to top
View user's profile
DKase
Tractor Expert


Joined: 07 Apr 2002
Posts: 3286


Report to Moderator

PostPosted: Thu May 07, 2009 4:44 am    Post subject: Re: Post driver on a 685 Reply to specific post Reply with quote

Since no one has an answer for you I will try. First we need to know what type of pounder? Some have a cylinder and linkage that lifts the weight, and a trip that drops the weight. These simply plug into the remote couplers just like any other remote cylinder. Other pounders lift the weight with a 1 way hydraulic cylinder and the oil from that cylinder must be released very quickly to allow the cyl. to drop fast. They need a large hose for the return flow that goes directly to the hyd tank with no couplers and no restriction. Hope this helps. DK
 
Back to top
View user's profile
tom-ky
Regular


Joined: 07 Jun 2003
Posts: 175


Report to Moderator

PostPosted: Fri May 08, 2009 1:50 am    Post subject: Re: Post driver on a 685 Reply to specific post Reply with quote

Went and looked at this yestrday. he had the lines hookjed up wrong.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters