PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

2470 pulling problems


 
Post new topic    
View previous topic :: View next topic  
Author Message
Danboys
New User


Joined: 07 May 2009
Posts: 3


Report to Moderator
PostPosted: Thu May 07, 2009 5:16 pm    Post subject: 2470 pulling problems Reply to specific post Reply with quote
We have a 2470 with a pulling problems... To cut a long story short We fixed a noisy powershift this winter... Now the unit is in the field it shifts though all ranges & powershifts .. but when under load we loose traction ( as if the clutch is slipping) Ok it seems to be only in sum ranges.. ie in range 1 & all powershifts its fine... in range 2 powershit 1 it slips but in range 2 powershift 2 it pulls like a buger but try going in powershift 3 it slips...
Please Help
 
Back to top
View user's profile
jogl
Long Time User


Joined: 22 Jun 2003
Posts: 604
Location: SW Ontario

Report to Moderator
PostPosted: Fri May 08, 2009 2:29 am    Post subject: Re: 2470 pulling problems Reply to specific post Reply with quote
I can't offer any specific advice other than don't use that tractor until you get that power shift straightened out. It sounds like one of your clutch packs isn't right. Do you have a manual and some pressure gauges to check the pressures?

There are a couple of guys on this forum who have offered me good advice when I was asking about our 2870. Maybe they will respond to your post. Also, you should do some searching around in this forum. I'm pretty sure there was once a thread about clutch packs and pressures, etc.

Good Day,
JP.
 
Back to top
View user's profile
Danboys
New User


Joined: 07 May 2009
Posts: 3


Report to Moderator
PostPosted: Fri May 08, 2009 4:05 am    Post subject: Re: 2470 pulling problems Reply to specific post Reply with quote
Yes i have the big red book... but still not sure .. would hate to pull her back down & could have fixed her via pressures.. i dont have gauges
Thanks anyway
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters