Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Argh!! Case 870 hyd help needed.

Post new topic    
View previous topic :: View next topic  
Author Message
Dave from MN
Tractor Expert

Joined: 19 Aug 2007
Posts: 2452

Report to Moderator

PostPosted: Wed Apr 14, 2010 2:25 pm    Post subject: Argh!! Case 870 hyd help needed. Reply to specific post Reply with quote

Ok, have an 870 case. It had a loader on it, just took it off this past wekend and put the planter on the tractor. The loader was able to lift 1000#+ bales up high no issues and if you left it up and shut down the ractor the loader didnt drop. Those were dual acting cylinders. Ok, so I connect 8 row JD 7000 planter, which has single acting cylinders for markers and lift. I can get the tractor to lift the planter, but as soon as I let the hyd lever go back to center position(home) the planter drops again. I havent tried the markers yet. Also, For some reason if I hook the single hose up to one of the sets of outlets, it doesnt lift or anything, I hook up to the other side outlets and I can only get it to lift when I move that lever forward, but if I swap outlets, it still doesnt lift when I pull the same lever back. Really frustrating me, the hydraulics all worked fine when I havde the loader on. The loader was all hooked up to the outlets so all I did was take them out like any other hyd hoses. Any knowledge on this out there?
Back to top
View user's profile
Adirondack case guy
Tractor Guru

Joined: 04 Mar 2010
Posts: 17474

Report to Moderator

PostPosted: Wed Apr 14, 2010 3:11 pm    Post subject: Re: Argh!! Case 870 hyd help needed. Reply to specific post Reply with quote

Case double acting remotes were paired 2 Top & 2 Bottom couplings, per circuit. Changing from RH couplings to LH couplings mearly changes the direction that you move the lever. Your single acting lift cylinder may function on either the top or bottom RH couplings with lever back rise,because of the weight of the planter, but I dought the marker will drop. There was not a float position on the remotes so you will have to plumb a relief circuit to the LH couplings back to sump.
Back to top
View user's profile
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

Jump to:  

We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters