Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Wc Front oil seal


 
Post new topic    
View previous topic :: View next topic  
Author Message
Texas Denny
Long Time User


Joined: 24 Aug 2007
Posts: 868


Report to Moderator

PostPosted: Mon Dec 06, 2010 5:17 am    Post subject: Wc Front oil seal Reply to specific post Reply with quote

My 47 WC has started to leak from the front oil seal. Can this be replaced without pulling the pan? Thanks, Denny
 
Back to top
View user's profile
bjb in TX from Ne
Long Time User


Joined: 18 Mar 2009
Posts: 875


Report to Moderator

PostPosted: Mon Dec 06, 2010 6:05 am    Post subject: Re: Wc Front oil seal Reply to specific post Reply with quote

If I recall right from when I rebuilt my WC, Yes, you should be able to replace the front seal. The front seal is in the front cover. I think the oil pan seal on a lip that runs on the front block. You may want to get a manual to double check. If you can get the front pulley off, and get the seal out, you may even be able to replace it without removing the front cover.
 
Back to top
View user's profile
JMS/.MN
Tractor Guru


Joined: 05 Mar 2009
Posts: 12827


Report to Moderator

PostPosted: Mon Dec 06, 2010 10:49 am    Post subject: Re: Wc Front oil seal Reply to specific post Reply with quote

Yes- remove the radiator and front pulley. If you take off the front cover, be sure to center it perfectly before tightening the bolts. There is a bit of flex in the seal, so support the cover before tightening.
 
Back to top
View user's profile
Texas Denny
Long Time User


Joined: 24 Aug 2007
Posts: 868


Report to Moderator

PostPosted: Mon Dec 06, 2010 2:03 pm    Post subject: Re: Wc Front oil seal Reply to specific post Reply with quote

I"ve got the IT manual. Will try it this weekend.
 
Back to top
View user's profile
Texas Denny
Long Time User


Joined: 24 Aug 2007
Posts: 868


Report to Moderator

PostPosted: Mon Dec 06, 2010 2:04 pm    Post subject: Re: Wc Front oil seal Reply to specific post Reply with quote

Thanks. Will giver 'er a try this week end.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters