Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

267 weight


 
Post new topic    
View previous topic :: View next topic  
Author Message
Roger Roemen
Regular


Joined: 25 Dec 2007
Posts: 132


Report to Moderator

PostPosted: Thu Dec 15, 2011 8:20 am    Post subject: 267 weight Reply to specific post Reply with quote

I am going to do an out of frame over haul of a 267 engine. I would like to put it on an engine stand but I am afraid of the weight. Do any of you have an estimate of the weight of the block without heads. I appreciate any help. Roger
 
Back to top
View user's profile
J HIKEMPER
Guest






Report to Moderator

PostPosted: Thu Dec 15, 2011 8:31 am    Post subject: Re: 267 weight Reply to specific post Reply with quote

depends on what you have for an engine stand // do you have a chinese ,japanese ,dirtyknees engine stand from flim flamwallyworld?? , ... if not bolt that 267 on there ,, shouldnt be much heavier than a big block ford v -8
 
Back to top
RGMartin
Tractor Guru


Joined: 14 Jan 2011
Posts: 3724


Report to Moderator

PostPosted: Thu Dec 15, 2011 8:44 am    Post subject: Re: 267 weight Reply to specific post Reply with quote

The bare block weighs as much as a fully built small block Ford. This is from my own scientific testing of wrestling one around by hand.

A complete engine will make the tail end of a DB 1200 awfully light when using a loader to install.

A stack of pallets seemed like a better idea to assemble the bottom end than a Harbor Freight engine stand.
 
Back to top
View user's profile
INCase
Tractor Expert


Joined: 22 Jul 2002
Posts: 2389
Location: Indiana

Report to Moderator

PostPosted: Fri Dec 16, 2011 8:48 am    Post subject: Re: 267 weight Reply to specific post Reply with quote

unfortunately i had to scrap one (I listed it for 2 years but no one wanted it!) and it was very close to 500lbs +/- with sleeves only no other parts.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters