Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

TD15C engine swap.

Post new topic    
View previous topic :: View next topic  
Author Message
jeff Lowery

Report to Moderator

PostPosted: Tue Oct 02, 2012 9:44 am    Post subject: TD15C engine swap. Reply to specific post Reply with quote

I am in the process of pulling a blown engine out of a TD15c. It has the DT466 in it and I am replacing it with another DT466. Just at a quick glance it looks as if the torque converter will need to be pulled with the motor to gain access to the bolts on the rear of the engine. What is the easiest way to pull this engine? It has the powershift transmission.
Back to top
Tractor Guru

Joined: 11 Apr 2010
Posts: 5064
Location: Dover Tenn.

Report to Moderator

PostPosted: Thu Oct 04, 2012 3:14 pm    Post subject: Re: TD15C engine swap. Reply to specific post Reply with quote

Jeff; Several ways ,some folks lean the hard nose over with the radiator in it. If the tractor is very old the pins are hard to pull. I always thought it was faster to remove the fiberglass dash shroud then the 2 boldts on each side of the dash frame. Ten you will have celar acess to the mount boldts. Absolutely not necessary to pull the torque, Simply go all the around the torque mount boldts, remove them you will find that the torque will sit on the mounts and may tilt back just a little. Removbe the front engine FAN, kinda hard to get to the boldts. lay the fan up against the radiator. Remove the front two mount boldts slide the engine foward 4 inches and lift out. Flip side if you want to remove with torque just pull the rear mounts, remove the pumps,they will slide back with hoses still attached , remove the drive line and lift the entire engine and torque.
Not reall much diffrence more of just what you prefer. NO internal torque boldts, recessed star gear drive /
E-mail open if you need more info.
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Crawlers, Dozers, Loaders and Backhoes All times are GMT - 8 Hours
Page 1 of 1

Jump to:  

Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters