Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

1365 oliver thrust washers

Post new topic    
View previous topic :: View next topic  
Author Message
lonnie foster

Report to Moderator

PostPosted: Sat Dec 29, 2012 8:58 pm    Post subject: 1365 oliver thrust washers Reply to specific post Reply with quote

the thrust washers came out of my 1365 oliver engine.can I replace them from the bottom,without removeing the engine? would appreciate any help thanks Lonnie
Back to top
B A Star
Long Time User

Joined: 05 Mar 2009
Posts: 820

Report to Moderator

PostPosted: Sat Dec 29, 2012 10:37 pm    Post subject: Re: 1365 oliver thrust washers Reply to specific post Reply with quote

   I assume that you are talking about the engine crankshaft thurst bering.  I don't have very good news for you.  The thurst bearing is two pieces that are not connected to the main bearing.  they fit into a machinedd area in the crankcase and machined area in the mating main bering cap.  The main bearing cap part has a tang to prevent rotation.
   If it has gone far enough that the bearings have fallen out it is disassemble time for the crankshaft.  You will probably see damage to the thurst surface on the crankshaft and have damage in the main journal web in the crankcase.  I have seen them where the web/cap is worn away to the point there is no longer a step to hold the bearing.  After disassembly you find that you have wear let me know and I will send you the reclaim proceedure.
   This model has a PTO control lever to engage and disengage the PTO.  Should the lever be left constantly in the disengage position it is always pushing the PTO clutch/flywheel/crankshaft assembly against the thurst bearing.  This is called out in cap letters in the operators manual.  leaving the lever in the disengage position is more than likely the cause for your failure.
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Oliver, Cletrac, Coop and Cockshutt All times are GMT - 8 Hours
Page 1 of 1

Jump to:  

Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters