Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

I got a problem


 
Post new topic    
View previous topic :: View next topic  
Author Message
Jerry D in NC
Guest






Report to Moderator

PostPosted: Fri May 25, 2007 7:00 pm    Post subject: I got a problem Reply to specific post Reply with quote

I have a neighbor that has a JD 5425 that has no flow control for the hydraulics. We are working on a Hoelscher bale system for him and it is too fast. Does any one know of a restrictorfor the lines that would reduce the flow????

 
Back to top
Michael Price
Guest






Report to Moderator

PostPosted: Fri May 25, 2007 7:15 pm    Post subject: Re: I got a problem Reply to specific post Reply with quote

What about the knob under the seat? I know that controls the speed of the 3pt but it may control all the hydraulics to.

 
Back to top
Gerald J.
Guest






Report to Moderator

PostPosted: Fri May 25, 2007 7:18 pm    Post subject: Re: I got a problem Reply to specific post Reply with quote

Available with a micrometer control in a check valve arrangement. Sold by Burden's Surplus Center, Northern Tool, and Baum Hydrauics. Pictured here on my gas 4020.

Gerald J.

 

Back to top
Jerry D in NC
Guest






Report to Moderator

PostPosted: Sat May 26, 2007 4:20 am    Post subject: Re: I got a problem Reply to specific post Reply with quote

The 5425 does not have any flow control at all. Even for the 3pt

 
Back to top
Michael Price
Guest






Report to Moderator

PostPosted: Sat May 26, 2007 3:34 pm    Post subject: Re: I got a problem Reply to specific post Reply with quote

They must have did away with it when they went to the electric controls. What you would probably need to do is just get a ball valve for hydraulics and put it in the line and just close it off until you get the right speed. I think the valves are only about 16 bucks.

 
Back to top
Jerry D in NC
Guest






Report to Moderator

PostPosted: Mon May 28, 2007 6:29 pm    Post subject: Re: I got a problem Reply to specific post Reply with quote

The 5425 does not have any flow control at all. Even for the 3pt

 
Back to top
Jerry D in NC
Guest






Report to Moderator

PostPosted: Tue May 29, 2007 8:29 am    Post subject: Re: I got a problem Reply to specific post Reply with quote

The 5425 does not have any flow control at all. Even for the 3pt

 
Back to top
:   
Post new topic    Yesterday's Tractors Forum Index -> Implement Alley All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters