Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Governor on B works, but......


 
Post new topic    
View previous topic :: View next topic  
Author Message
Rex in Australia
Guest






Report to Moderator

PostPosted: Thu May 10, 2007 11:02 pm    Post subject: Governor on B works, but...... Reply to specific post Reply with quote

Latest on the governor, it now works but I can't get many revs as it pulls the throttle back very strongly. I note that the spring on the linkage between the governor arm and carby is missing a spring. Should that spring pull the throttle on to assist? The short governor spring does not appear to be strong enough to hold any amount of revs on.
Once again, thanks for the input. It is much appreciated.
God Bless,
Rex

 
Back to top
JMS/MN
Guest






Report to Moderator

PostPosted: Fri May 11, 2007 5:50 am    Post subject: Re: Governor on B works, but...... Reply to specific post Reply with quote

The rod with the hole in the middle holds the anti-surge spring- gets hooked to a manifold bolt. It steadies the rod, so the engine runs smoother.

 
Back to top
Dick L
Guest






Report to Moderator

PostPosted: Fri May 11, 2007 6:03 am    Post subject: Re: Governor on B works, but...... Reply to specific post Reply with quote

If (IF) it is an original spring it would be strong enough and you will probably need to adjust the cross over arm from the governor. If you bend the arm more than needed it will cause surging of the engine. I do that adjustment by standing in front of the tractor and holding the arm just above the governor housing with an adjustable wrench. I unhook the throttle rod and place a pipe over the end to bend the cross over arm. On the early B, that Rod posted the drawing of, you would have to use two adjustable wrenches. (I stress to you that over bending will cause the engine to surge.)

 
Back to top
Rex in Australia
Guest






Report to Moderator

PostPosted: Fri May 11, 2007 12:12 pm    Post subject: Re: Governor on B works, but...... Reply to specific post Reply with quote

Thanks so much good people. The spring certainly looks like an original, but the holes are worn a bit so that would lose some travel.
I have it running not too badly now so will have a bit more of a play with it.
Once again, thank you all so much.
Rex

 
Back to top
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters