Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

refilling hyd lift cylinder


 
Post new topic    
View previous topic :: View next topic  
Author Message
terry palmer
Guest






Report to Moderator

PostPosted: Fri May 11, 2007 12:30 pm    Post subject: refilling hyd lift cylinder Reply to specific post Reply with quote

I finally found lift cylinders for my wd45. Now how do I refill them and bleed out the air? Do I losen the large nut were the rod comes out? Are there any other things I should do first?

 
Back to top
Aaron SEIA
Guest






Report to Moderator

PostPosted: Fri May 11, 2007 1:43 pm    Post subject: Re: refilling hyd lift cylinder Reply to specific post Reply with quote

Easiest way is just hook it all up and let it pump up and down a few times. Eventually the air will all bleed out. If you hook the hyd hose up with the cylinder retracted (short), then most of the air will be out anyway.
Aaron SEIA

 
Back to top
old
Guest






Report to Moderator

PostPosted: Fri May 11, 2007 2:04 pm    Post subject: Re: refilling hyd lift cylinder Reply to specific post Reply with quote

Just hook them up and use them after 3 or 4 times of lifting and lowering they will have bled all the air out on there own

 
Back to top
terry palmer
Guest






Report to Moderator

PostPosted: Sat May 12, 2007 6:22 am    Post subject: Re: refilling hyd lift cylinder Reply to specific post Reply with quote

thanks alot. todays project.

 
Back to top
terry palmer
Guest






Report to Moderator

PostPosted: Mon May 14, 2007 1:47 pm    Post subject: Re: refilling hyd lift cylinder Reply to specific post Reply with quote

Worked great and alot easier than taking them off. Now they will not stay in one position floats up and down. It picks up my rototiller no sweat it just will not hold in one place. If I have the control all the way down slowly it will creap up. Suggestions?

 
Back to top
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters